Instrukcja obsługi Beltronics GT-360
Beltronics
Nie skategoryzowane
GT-360
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Beltronics GT-360 (10 stron) w kategorii Nie skategoryzowane. Ta instrukcja była pomocna dla 13 osób i została oceniona przez 7 użytkowników na średnio 4.8 gwiazdek
Strona 1/10
Programming
Press BRT to go from Press VOLUME + or – to change
one category to the next your setting within a category
User Mode Advanced* Access and customize all Settings and Preferences
Novice Access and customize units and display color, (all other
Settings are set to factory defaults)
NOTE: Switch back to Advance mode to view all Preferences
Pilot Scan Bar* Scanning Bar with Full Word
Full Word Full Word: AutoScan, Auto NoX, or Highway
Display Color Copper*/Blue/Green/Red Set color to match your vehicle’s dash display
Speed Display On* Displays current speed
O Displays battery voltage
Cruise Alert O / 20-160 mph Oers double beep alert tones below specied speed
20 mph*
Over Speed O / 20-160 mph Reminds you when you exceed a specied speed
70 mph*
Meter Mode Standard* Single band with front and rear signal strength bar graphs
Tech Single band with numeric frequency and front and rear
signal strength bar graphs
Basic Simple messages replace bands:
Caution (if traveling below cruise alert limit)
Slow Down (if traveling above cruise alert limit)
Tones Standard* Standard Beltronics alert tones
Mild Mild doorbell chime alert tones
AutoMute Low/Med*/High/O
Automatically reduces audio to preferred volume during alert
AutoLock On* / O Automatically stores and locks out false alarms
Units English*/Metric Units for distance and speed
Language English*/Espanol Language for voice and text
Voice On* / O Voice announcements
GPS Filter On* / O Enables GPS-powered features
Press and hold the BRT and SEN buttons to access Programming. To exit Programming, simply wait a few
seconds without pressing a button. The unit will display Completed to conrm your selections.
7
Programming
AutoPower O Power turns on or o depending on your vehicle’s ignition
type (constant power or switched)
1 Hour Powers o automatically after 1 hour
2 Hours Powers o automatically after 2 hours
4 Hours* Powers o automatically after 4 hours
8 Hours Powers o automatically after 8 hours
NOTE: If AutoPower is on, to save screen life the display screen goes
blank after 30 minutes without moving.
Band Enables Default* Default Settings
Modied Band Enables have been modied from their default settings
Press SEN to go from one Press VOLUME + or – to change
band category to the next your setting within a category
X Band On* / O
K Band On* / O Freq: 24.050-24.250 GHz
NOTE: When K Band is o, you can select separate segments of the
band to turn on or o.
KN1 On* / O Freq: 24.050 - 24.110 GHz
KN2 On* / O Freq: 24.110 - 24.175 GHz
KN3 On* / O Freq: 24.175 - 24.250 GHz
KN4 On / O* Freq: 23.950 - 24.050 GHz
Ka Band On* / O Freq: 33.400-36.000 GHz
NOTE: When Ka Band is o, you can select separate segments of the band to turn
on or o.
KaN1 On / O* Freq: 33.400 - 33.700 GHz KaN6 On / O*
Freq: 34.800 - 35.160 GHz
KaN2 On / O* Freq: 33.700 - 33.900 GHz KaN7 On / O*
Freq: 35.160 - 35.400 GHz
KaN3 On* / O Freq: 33.900 - 34.200 GHz KaN8 On* / O
Freq: 35.400 - 35.600 GHz
KaN4 On* / O Freq: 34.200 - 34.600 GHz KaN9 On / O*
Freq: 35.600 - 35.840 GHz
KaN5 On* / O Freq: 34.600 - 34.800 GHz KaN10 On / O*
Freq: 35.840 - 36.000 GHz
Ka Band On* / O
Ka-POP On / O*
Laser On* / O
TSR On* / O Automatically rejects trac ow sensors-monitoring false alarms
Marker Enable On* / O Default Settings
Modied Marker Enables have been modied from their default settings
NOTE:
AutoPower only
works with constant
power ignition
8
Programming
9
Press SEN to go from one Press VOLUME + or – to change
marker category to the next your setting within a category
Other On* / O Other location
Redlight On* / O Red light camera
Red & Speed On* / O Red light & speed camera
Speed Cam On* / O Speed camera
Air Patrol On / O* Known aircraft patrolled areas
NOTE: User cannot mark an air patrol location
Speed Trap On* / O Speed trap
Air Patrol On / O* Known aircraft patroled areas
NOTE: User cannot mark an Air Patrol location
Clear Locations Marked Clear all user Marked locations. Press SEN button to conrm
Lockouts Clear all lockouts. Press SEN button to conrm
Defender Clear all DEFENDER data. Press SEN button to conrm
Format Clear DEFENDER database, all markers, and all lockouts.
Press SEN button to conrm
*Default Setting
Specyfikacje produktu
| Marka: | Beltronics |
| Kategoria: | Nie skategoryzowane |
| Model: | GT-360 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Beltronics GT-360, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Nie skategoryzowane Beltronics
14 Marca 2025
14 Marca 2025
14 Marca 2025
Instrukcje Nie skategoryzowane
- Nie skategoryzowane Walrus Audio
- Nie skategoryzowane WyreStorm
- Nie skategoryzowane HMD
- Nie skategoryzowane Thule
- Nie skategoryzowane Sogo
- Nie skategoryzowane Induction Dynamics
- Nie skategoryzowane PoLabs
- Nie skategoryzowane Atlas Sound
- Nie skategoryzowane Cooler Master
- Nie skategoryzowane Ikea
- Nie skategoryzowane Velleman
- Nie skategoryzowane JLCooper
- Nie skategoryzowane CLIMAQUA
- Nie skategoryzowane Boss
- Nie skategoryzowane Panasonic
Najnowsze instrukcje dla Nie skategoryzowane
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025