Instrukcja obsługi Binatone BabySense 5
Binatone
Elektroniczna niania
BabySense 5
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Binatone BabySense 5 (2 stron) w kategorii Elektroniczna niania. Ta instrukcja była pomocna dla 41 osób i została oceniona przez 21 użytkowników na średnio 4.9 gwiazdek
Strona 1/2
Breathing & Movement Monitor
5
Medically approved
Sensor | Do not use | Sensor
Slot
Illustration 6
Sensor | Do not use | Sensor
Hanging hook
Blue breathing
movement
indicator light Red alert
alarm light
Low battery
warning light On/Off
button
Illustration 8
Speaker
Control
Unit
Cable Cable
Bed/Crib
base
Control unit holder
Illustration 5
13
2
Ensure you read this user guide before installing and
using the product.
Babysense is a high quality, high sensitivity electronic
device which must be handled with care:
• Do not handle roughly, drop or throw.
• Follow the installation instructions carefully to
ensure that it is installed securely and correctly.
• Babysense is not a toy. Do not allow children of any
age to play with it.
• Do not put any additional baby or pet in the bed.
Babysense cannot be used for two infants in one bed.
• You must undertake the performance test daily of
the Babysense monitor (as set out on page 3).
• Do not operate a vaporiser or ventilator directly
towards the bed.
• To avoid possible danger from sensor cords,
ensure that excess cords are pulled back under
the mattress, secured with the included cable tie
and are not visible or reachable.
• Install 4 new and identical size AA 1.5 volt batteries,
preferably alkaline.
• IMPORTANT: It is strongly advised that every
caregiver learn how to give first aid.
"Babysense" monitors and alerts, but cannot prevent
cessation of breathing. The responsibility for applying first
aid rests on caretakers. The "Babysense" senses breathing
movements and motion only, and cannot monitor
other occurrences. The purpose of the device is to alert
when stopping or slowing of breathing and
movement occur.
"Babysense" is a unique safety system which has helped
save infants, giving parents (or caretaker) assurance,
by enabling intervention in the event of irregular
breathing movement or distress, before it becomes
critical. There are a number of cautionary steps
which are internationally recommended for SAFE
SLEEPING:
* Always lay your baby to sleep on his or her back.
* Refrain from smoking near or around your baby.
* Avoid over-heating the baby's surroundings.
* Do not leave any objects near your baby that can
cause suffocation.
Babysense is an addition to these precautions.
"Babysense" is a home breathing movement monitor
for basically healthy infants up to one year of age,
and is not to be relied on for use with high-risk infants
requiring constant medical supervision.
"Babysense" continually detects the baby's motion and
breathing movements, and will set off a sound and
visual alarm if movement stops for 20 seconds or if the
breathing rate slows to below 10 breaths per minute if
the baby's breathing. The system's non-touch sensor
pads under the mattress monitor baby's movement
without restraining him.
1. Insert, in accordance with the markings, 4 new and
identical size AA 1.5 volt batteries, preferable alkaline.
Close the battery cover.
Note: Do not mix old and new batteries.
Note: For replacing the batteries, remove the battery
cover by inserting a flat screwdriver into the opening
recess (see illustration 7).
Note: Please dispose of used batteries in accordance
with local waste regulations.
2. Place control unit holder on the base of the crib
or bed and in between two bars as shown in
illustration 1.
3. Make sure the sensitivity adjustor, located on the back
of the sensor pads, is positioned on level 3
(see illustration 2).
4. Sensor pad installation:
• When using for an infant not yet able to crawl, place
one sensor pad as shown in illustration 3. Make sure the
sensor is placed underneath the baby's position in the crib.
Warnings
Principal Of Operation
Installation
Please note
9. Place mattress firmly on top of sensor pads. If the
mattress cannot be in contact with the sensor pads,
or if the bed base is soft, padded or contains
springs, place extra plywood on the bed base, place
the sensor pads on the plywood and place the
mattress firmly on top.
IMPORTANT: To avoid possible danger from sensor
cords, ensure that excess cords are pulled back
under the mattress, secured with the included cable
tie and are not visible or reachable.
See illustration 8 for layout of control unit featuring:
• On/Off button.
• Blue breathing movement indicator light.
• Acoustic and visual red alarm light.
• Low battery red warning light.
"Babysense" is ready for operation and use once
the installation is complete. To operate, follow the
below instructions:
• Place your baby in the crib/bed.
• Turn control unit on by pressing On/Off button.
• Red control lights switch on briefly and a double
click sound is heard.
• When breathing and movement is sensed, the
blue light flashes.
• Acoustic any visual red light alarms are activated
if the baby's breathing stops or slows significantly.
• If the red low-battery warning light flashes,
replace all batteries as soon as possible. If in
addition clicking is heard, all batteries must be
replaced immediately.
• Turn off by pressing On/Off button before taking
your baby out of the crib/bed.
User Guide
0
1
2
3
Illustration 2
• When the baby begins to crawl, and is able to move
onto areas not "covered" by a single sensor pad, attach
the second sensor and place the two sensors as shown
in illustration 3.
PLEASE NOTE: The sensors shall be placed with the
marking “THIS SIDE UP” facing upfront.
5. Pass the cord(s) of the sensor pad(s) through
special openings in the holder. (see illustration 4)
6. Attach end(s) of the cord(s) to the outlets
marked "SENSOR" on the back of control unit
(see illustration 5 and 6). When using one sensor
pad, attach to either “SENSOR” outlet.
PLEASE NOTE: Do not attach any cable to the
blocked socket, marked "DO NOT USE"
7. Should the design of the crib/bed not allow proper
installation with the control unit holder, please use the
optional hanging hook (see illustration 6) and hang the
control unit from the bottom edge of the crib.
8. Press control unit holder or hanging hook firmly
into slot in back of control unit (see illustration 5 and 6).
"Babysense" is a highly sensitive device which
monitors baby's breathing movements through the
mattress during sleep. There are two main causes of
malfunction - technical malfunctions and
malfunctions due to environmental factors.
In order to minimise technical problems, follow
installation and operation instructions carefully.
Due to the high sensitivity of "Babysense", it can
be influenced by fans, wind, air conditioning, and
so forth. Such environmental effects could be
picked up by the sensors on a similar level to that of
breathing movements, thus preventing or delaying
alarm activation.
Do not conduct performance test by picking up
baby out of bed and waiting for the alarm to sound
• The performance test should be conducted
while the baby is not in bed.
• Turn device on and take two steps back from bed.
• Ensure the alarm goes off within 20 seconds
(due to absence of breathing movements).
• The alarm may sound with or without
preliminary ticking.
• Check the alarm can be heard in all locations
throughout the home or place of care.
• In case the alarm does not sound within 20
seconds refer to troubleshooting at page 5.
• The performance test must be conducted daily.
Isolated cases of false alarms are possible. Check if caused
by faulty connection of the sensor pad(s) to the control
unit, connection of only one sensor pad when the baby
can move off the immediate area, connection of two
sensor pads far apart from each other when the baby is
not crawling yet, or failure of the sensor pads to be
directly against the mattress.
In case of false alarms, kindly refer to troubleshooting
guide. If the problem cannot be solved, please
contact your nearest BABYSENSE representative.
Act immediately according to the following:
1. Approach the bed and check that baby is breathing.
Note pallor (color of skin), muscle tone and movement.
2. If baby does not seem normal, pinch baby's heel
and check that there is no cause for choking,
such as an object lodged in baby’s throat.
When breathing resumes, consult a doctor.
3. If breathing does not resume, apply first aid and seek
medical assistance immediately.
Sensor | Do not use | Sensor
Slot
Battery
cover
Blocked socket
DO NOT USE
“Sensor”
socket
Illustration 7
Opening
recess
Speaker
Layout of control unit
Operation
Testing Operation
Technical malfunction
Environmentally caused malfunction
Conduct this performance test daily
False alarms
In the event of alarm
Cables
Illustration 4
Control unit
holder
Illustration 1
Control unit holder
Cables
Sensor
Sensor
Sensor pads
(Under mattress)
Control unit
Illustration 3
Top crib/bed view
For babies not
yet able to crawl
For crawling babies
Top crib/bed view
Specyfikacje produktu
| Marka: | Binatone |
| Kategoria: | Elektroniczna niania |
| Model: | BabySense 5 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Binatone BabySense 5, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Elektroniczna niania Binatone
2 Września 2024
23 Sierpnia 2024
23 Sierpnia 2024
23 Sierpnia 2024
17 Sierpnia 2024
Instrukcje Elektroniczna niania
- Philips
- NUK
- Konig
- Lindam
- Stabo
- SereneLife
- Kodak
- Ansmann
- EZVIZ
- GoClever
- Tommee Tippee
- Topcom
- Esscom
- Jablotron
- Safety 1st
Najnowsze instrukcje dla Elektroniczna niania
28 Stycznia 2025
27 Stycznia 2025
26 Stycznia 2025
25 Stycznia 2025
25 Stycznia 2025
25 Stycznia 2025
25 Stycznia 2025
25 Stycznia 2025
25 Stycznia 2025
25 Stycznia 2025