Instrukcja obsługi Cateye CC-FR7CL

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Cateye CC-FR7CL (2 stron) w kategorii komputer rowerowy. Ta instrukcja była pomocna dla 14 osób i została oceniona przez 3 użytkowników na średnio 4.6 gwiazdek

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Modifications

The FCC requires the user to be notified that any changes or modifications made to this device that are

not expressly approved by Cat Eye Co., Ltd. may void the user’s authority to operate the equipment.

1

2

3

4

CATEYECordless 7

CYCLOCOMPUTER CC-FR7CL

EOWNER’S MANUAL

®

Installation of Computer:

Secure bracket to handlebar with nylon ties (fig. A).

Slide computer into mount until it snaps in place.

Mount the wheel magnet to a spoke on the front

wheel (fig.B), so the magnet faces the sensor.

Secure the sensor to fork leg as shown (fig. C).

NOTE: The distance between the computer and the sen-

sor must not exceed 70 cm—if the sensor is too far

away from the computer head, the speed signal will not

register on the computer.

For best results, mount the sensor as high on the fork

leg as reasonably possible, so that the sensor is within

transmission range to the computer. However, the sen-

sor must be close enough to spokes to allow proper dis-

tance to magnet (see below).

Test by spinning the front wheel. Computer screen

should show speed. If not, make sure 1)the magnet is

close enough to sensor (within 5 mm); and 2)the sensor

is close enough to computer head (within 70 cm) and 3)

nothing is obstructing the line of sight between the sen-

sor and the computer head.

IMPORTANT! PLEASE READ INSTRUCTIONS COMPLETELY

BEFORE ATTEMPTING TO INSTALL AND USE YOUR CAT EYE

CORDLESS 7 COMPUTER.

Cordless 7

U.S. Pat. Nos.4633216/4636769/4642606/5236759 Pat. and Design Pat. Pending

Copyright© 2002 CATEYE Co., Ltd.

CCMFR7CL-021210 Printed in Japan 066600165 1

2

3

OK

2

3

12

3

4

5

Bracket

Sensor

(Transmitter)

Magnet

Nylon Ties (L x 2)

Nylon Ties (S x 2)

Sensor Pulse Indicator

Magnet's

center

Marking line

Less than 5mm

Spin

Max.

Distance

70 cm

1

3

2

NOTE: When the wheel rotates, the magnet MUST line up with the mark on the sensor.

ALSO NOTE:Magnet must pass within 5 mm of the sensor—if not, it will not trip the

sensor as it passes, and the computer will not register speed. Adjusting the sensor

position higher or lower on the fork leg or by rotating the sensor on the fork mount may

be required to achieve proper distance to the wheel magnet.

3

!

Press the SET button to lock in your choice---OR---

if you want to input previous mileage, hold the

MODE button (before pressing the SET button) for

2 seconds.

•Flashing Odometer digits will appear.

•MODE button increases the digit number.

•START/STOP button moves to the next digit.

•Press the SET button when complete.

Press All-Clear button (AC).

Computer Set-up (for first use, or after replacing battery)

Get your wheel

circumference

move to the next digit

•Stored data is erased.

•Computer power is started.

•Total Odometer read's "zero".

•All digits shown then fades.

•Flashing "km/h" remains.

Adjust between “mph” or “km/h” by pressing

the MODE button.

•Wheel circumference number is shown.

•Look at chart to find TIRE SIZE in "mm".

•To increase TIRE SIZE press MODE button.

•To decrease press START/STOP button.

•10-2999 mm can be registered.

•Press SET button when finished.

km/h mph

Setup Completed (To Tm)

Tire SizeL(mm)

12 x1.75935

14 x 1.501020

14 x 1.751055

16 x 1.501185

16 x 1.751195

18 x 1.501340

18 x 1.751350

20 x 1.751515

20 x 1-3/81615

22 x 1-3/81770

22 x 1-1/21785

24 x 11753

24 x 3/4Tubular1785

24 x 1-1/81795

24 x 1-1/41905

24 x 1.751890

24 x 2.001925

24 x 2.1251965

26 x 7/81920

26 x 1(59)1913

26 x 1(65)1952

26 x 1.251953

26 x 1-1/81970

26 x 1-3/82068

26 x 1-1/22100

26 x 1.402005

26 x 1.502010

26 x 1.752023

26 x 1.952050

26 x 2.002055

26 x 2.102068

26 x 2.1252070

26 x 2.352083

26 x 3.002170

27 x 12155

27 x 1-1/82161

27 x 1-1/42161

27 x 1-3/82169

650 x 35A2090

650 x 38A2125

650 x 38B2105

700 x 18C2070

700 x 19C2080

700 x 20C2086

700 x 23C2096

700 x 25C2105

700 x 28C2136

700 x 30C2170

700 x 32C2155

700C Tubular2130

700 x 35C2168

700 x 38C2180

700 x 40C2200

1

2

3

increase

the figure

increase

the figure

AC Button

decrease

the figure

Use the below table

as the rough guide.

The tire size is marked on

both sides of the tire.

AC buttonSET button

ST./STOP button

MODE button

L mm

In this state Auto Time is ON.

ST./STOP

ST./STOP

MODE

MODE

MODE

SET

SET

SET

MODE

Precautions

•Do not concentrate too much on the computer operations while riding.

•Be sure to securely mount the magnet, sensor and bracket on your bicycle,

and alweys check to insure they are mounted securely.

•Used batteries must be disposed of properly and in accordance with all

local regulations.

•Never disassemble the computer.

•For cleaning, use mild soap and a soft cloth. Wipe dry with a soft cloth. Paint

thinner, benzine, alcohol or other chemicals may damage the surface.

About cordless system

The sensor picks up the wheel revolution signal and transmits the signal to the computer; the

computer calculates and displays the data on the screen.

CAUTION: In order to prevent external signal interference, the signal reception range is limited. For

best performance, the distance between the sensor and the computer must be kept within 70cm.

Attach the sensor at the upper part of your fork so that the distance becomes less than 70cm. The

signal reception range may shorten as a result of low temperature or lowered battery power.

In the following places and circumstances, interference may occur, resulting in malfunction:

•Near railroad crossing; in train cars.

•Near other cordless devices/television/personal computer/high power lighting system.

•Near the places where strong electromagnetic wave is generated; near television/ radio station; near

radar base.

•When being very close to another bicycle which also has a cordless cyclocomputer on its handlebar.

4

2

Sensor Screw

Sensor Base

Sensor Base

Front Fork

(fig. C)

(fig. B)Spoke

5

1

Lever

Slide

Click

(fig. A)

Mounting View

Front Fork

Specyfikacje produktu