Instrukcja obsługi Chief RPA227
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Chief RPA227 (1 stron) w kategorii Wsparcie dla płaskich paneli. Ta instrukcja była pomocna dla 13 osób i została oceniona przez 7 użytkowników na średnio 4.7 gwiazdek
Strona 1/1
I N S T A L L A T I O N I N S T R U C T I O N S
Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes
no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-002034 Rev01
©2009 Milestone AV Technologies,
a Duchossois Group Company
05/09
SSB-227, SSM-227, SLB-227 and SLM-227 Interface Brackets
SSB-227, SSM-227, SLB-227 and SLM-227 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place the interface bracket onto the bottom of the projector and align the three holes in the bracket with the three threaded inserts in the
bottom of the projector.
4. Using the three M4 X 10mm mounting screws and washers, secure the bracket to the projector and tighten all fasteners at this time.
NOTE: Security screws can be substituted when mounting interface bracket to projector by using the parts and installation instructions in the
All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (3) Washer, M4
(4) 10-24 Thumb Nuts ** (3) Screw, Phillips Pan Head, M4 x 10mm
(1) All-Points Security Kit
**Only used when installing SLB Interface brackets.
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the
encircled locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style
interface bracket installation.
SLB-227
SLM-227
(
N
o
t
e
:
S
S
M
-
s
t
y
l
e
i
n
t
e
r
f
a
c
e
b
r
a
c
k
e
t
c
o
n
n
e
c
t
i
o
n
s
a
r
e
e
n
c
i
r
c
l
e
d
)
(Note:
S
S
B
-
s
t
y
l
e
i
n
t
e
r
f
a
c
e
b
r
a
c
k
e
t
c
o
n
n
e
c
t
i
o
n
s
a
r
e
e
n
c
i
r
c
l
e
d
)
Towards front of
projector
Towards front of
projector
Specyfikacje produktu
| Marka: | Chief |
| Kategoria: | Wsparcie dla płaskich paneli |
| Model: | RPA227 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Chief RPA227, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Wsparcie dla płaskich paneli Chief
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
Instrukcje Wsparcie dla płaskich paneli
- Wsparcie dla płaskich paneli Icy Box
- Wsparcie dla płaskich paneli SMS Smart Media Solutions
- Wsparcie dla płaskich paneli Gabor
- Wsparcie dla płaskich paneli B-tech
- Wsparcie dla płaskich paneli Anthro
- Wsparcie dla płaskich paneli SmartMetals
- Wsparcie dla płaskich paneli Ematic
- Wsparcie dla płaskich paneli HP
- Wsparcie dla płaskich paneli Panduit
- Wsparcie dla płaskich paneli Peerless
- Wsparcie dla płaskich paneli BenQ
- Wsparcie dla płaskich paneli Silverstone
- Wsparcie dla płaskich paneli StarTech.com
- Wsparcie dla płaskich paneli Premier
- Wsparcie dla płaskich paneli LC-Power
Najnowsze instrukcje dla Wsparcie dla płaskich paneli
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
28 Stycznia 2025
28 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025