Instrukcja obsługi Chief RSMA285
Chief
Wsparcie dla płaskich paneli
RSMA285
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Chief RSMA285 (1 stron) w kategorii Wsparcie dla płaskich paneli. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 6.5 użytkowników na średnio 4.7 gwiazdek
Strona 1/1
I N S T A L L A T I O N I N S T R U C T I O N S
Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes
no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-002091 Rev00
©2011 Milestone AV Technologies,
a Duchossois Group Company
05/11
SSB-285, SSM-285, SLB-285 and SLM-285 Interface Brackets
SSB-285, SSM-285, SLB-285 and SLM-285 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place the interface bracket onto the bottom of the projector, aligning the mounting holes in the bracket with the threaded inserts in the
bottom of the projector and ensuring that triangle in bracket points towards front of projector.
4. Position M4 x 10mm mounting screws with M4 flat washers into the threaded inserts. Tighten all fasteners at this time, securing the bracket
to the projector.
NOTE: Security screws can be substituted when mounting Interface bracket to projector by using the parts and installation instructions in the
All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (4) Screw, Phillips Pan Head, Machine, M4 x 10mm
(4) 10-24 Thumb Nuts ** (4) Washer, M4
(1) All-Points Security Kit (1) 5/32" Security Hex Key
**Only used when installing SLB/SSB interface brackets.
NOTE: Specific to SSB-style and SSM-style interface bracket installation: All appropriate screws come pre-installed in the circled locations above.
DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style interface bracket installation.
Note: SSB-style interface bracket connections are circled. Note: SSM-style interface bracket connections are circled.
SLB-285 SLM-285
Towards front
of projector
Towards front
of projector
Specyfikacje produktu
| Marka: | Chief |
| Kategoria: | Wsparcie dla płaskich paneli |
| Model: | RSMA285 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Chief RSMA285, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Wsparcie dla płaskich paneli Chief
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
Instrukcje Wsparcie dla płaskich paneli
- Wsparcie dla płaskich paneli Zaor
- Wsparcie dla płaskich paneli Pyle
- Wsparcie dla płaskich paneli Rocstor
- Wsparcie dla płaskich paneli Pioneer
- Wsparcie dla płaskich paneli BenQ
- Wsparcie dla płaskich paneli Hitachi
- Wsparcie dla płaskich paneli Proaim
- Wsparcie dla płaskich paneli Sven
- Wsparcie dla płaskich paneli Bretford
- Wsparcie dla płaskich paneli Luxor
- Wsparcie dla płaskich paneli Silverstone
- Wsparcie dla płaskich paneli Atdec
- Wsparcie dla płaskich paneli Barkan
- Wsparcie dla płaskich paneli NeoMounts
- Wsparcie dla płaskich paneli Dell
Najnowsze instrukcje dla Wsparcie dla płaskich paneli
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
28 Stycznia 2025
28 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025