Instrukcja obsługi Chief SLB256
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Chief SLB256 (1 stron) w kategorii Wsparcie dla płaskich paneli. Ta instrukcja była pomocna dla 13 osób i została oceniona przez 7 użytkowników na średnio 4.8 gwiazdek
Strona 1/1
I N S T A L L A T I O N I N S T R U C T I O N S
Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes
no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-002046 Rev00
©2009 Milestone AV Technologies,
a Duchossois Group Company
11/09
SSB-256, SSM-256, SLB-256 and SLM-256 Interface Brackets
SSB-256, SSM-256, SLB-256 and SLM-256 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
**Only used when installing SLB/SSB interface brackets.
NOTE: Specific to SSB-style and SSM-style interface bracket installation: All appropriate screws come pre-installed in the circled locations.
DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style interface bracket installation.
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place three spacers on bottom of projector, aligning them with three threaded inserts on bottom of projector.
4. Place interface bracket onto spacers on bottom of projector, aligning the mounting holes in bracket with threaded inserts in bottom of
projector, and ensuring that triangle in bracket points towards front of projector.
5. Position two M4 x 16mm pan head mounting screws with two M4 flat washers into the outside threaded inserts, and the M4 x 16mm flat
head mounting screw into the threaded insert at front of bracket. Tighten all fasteners at this time, securing the bracket to the projector.
NOTE: Security screws can be substituted when mounting Interface bracket to projector by using the parts and installation instructions in the
All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (1) Screw, Phillips Flat Head, Machine, M4 x 16mm
(4) 10-24 Thumb Nuts ** (2) Screw, Phillips Pan Head, Machine, M4 x 16mm
(1) All-Points Security Kit (2) Washer, M4
(1) 5/32" Security Hex Key (3) Spacer, .50 x .218 x .25
Towards front
of projector
Towards front
of projector
SLB-256 SLM-256
Specyfikacje produktu
| Marka: | Chief |
| Kategoria: | Wsparcie dla płaskich paneli |
| Model: | SLB256 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Chief SLB256, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Wsparcie dla płaskich paneli Chief
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
Instrukcje Wsparcie dla płaskich paneli
- Wsparcie dla płaskich paneli Nabo
- Wsparcie dla płaskich paneli Samsung
- Wsparcie dla płaskich paneli Dell
- Wsparcie dla płaskich paneli HP
- Wsparcie dla płaskich paneli Dataflex
- Wsparcie dla płaskich paneli Elite Screens
- Wsparcie dla płaskich paneli Adicam
- Wsparcie dla płaskich paneli Iiyama
- Wsparcie dla płaskich paneli Multibrackets
- Wsparcie dla płaskich paneli Ematic
- Wsparcie dla płaskich paneli HQ
- Wsparcie dla płaskich paneli GPX
- Wsparcie dla płaskich paneli Zaor
- Wsparcie dla płaskich paneli Insignia
- Wsparcie dla płaskich paneli Pioneer
Najnowsze instrukcje dla Wsparcie dla płaskich paneli
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
28 Stycznia 2025
28 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025