Instrukcja obsługi Craftsman CMXZDCG498
Craftsman
Otwieracz do bramy garażowej
CMXZDCG498
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Craftsman CMXZDCG498 (4 stron) w kategorii Otwieracz do bramy garażowej. Ta instrukcja była pomocna dla 21 osób i została oceniona przez 11 użytkowników na średnio 4.6 gwiazdek
Strona 1/4
Master
Link
Trolley
Connector
Retaining
Slot
Threaded
Shaft
Front Rail
Section
Master
Link
Idler Pulley
Retaining
Slot
Trolley
Connector
To remove rail pry both
end tabs of front
rail slightly outward
Idler Bolt hole
(KEEP LARGER
ONE ON TOP)
NEW
FRONT RAIL
CORRECT
INCORRECT
Rail Tab
Rail Tab
Eight-Foot (2.4 m) Rail Extension Kit
Model CMXZDCG498
REFER TO GARAGE DOOR OPENER MANUAL FOR DETAILED INSTALLATION,
ADJUSTMENTS, AND SAFETY INFORMATION.
To prevent possible SERIOUS INJURY or DEATH:
• Disconnect ALL electric and battery power BEFORE performing ANY service
or maintenance.
The garage door MUST be in the fully closed position during installation.
®
Figure 2
Figure 1
BEFORE YOU BEGIN:
• The trolley must be in down (closed door) position during assembly and
installation. If you have a completely installed garage door opener, the rail/
opener assembly must be taken down. The UP and DOWN travel must be
readjusted after installation.
• Opener hanging brackets will require repositioning and the addition of an extra
bracket for stability due to increased rail length.
• This may require two people for installation.
IF THIS IS A NEW INSTALLATION:
Use the front (header) rail section, belt assembly, and longer emergency release
rope in this kit in place of those packaged with the garage door opener. Complete
the assembly, installation, and adjustment of the opener according to the garage
door opener manual. Ensure that an additional hanging bracket is added for
stability, as detailed below.
IF THIS IS AN EXISTING INSTALLATION, CONTINUE AS FOLLOWS:
1. Pull down on the emergency release handle, then disconnect the trolley from
the door arm.
2. Disconnect the rail/opener assembly from the header bracket and hanging
brackets, and place it on the floor.
3. Remove the sprocket cover from the opener sprocket and set aside.
4. Disconnect the master link from the trolley threaded shaft and belt; discard
(Figure 1).
5. Remove the spring/nut from the trolley and discard.
6. Remove idler pulley assembly and set aside.
7. Remove the belt assembly and discard.
8. Push the trolley back toward the opener. Disconnect the front rail section by
using a screwdriver tip to pry up the outer tab on each side of the rail, then
slide it off the center rail. Discard the front rail .(Figure 2)
9. Align the new front rail with the existing rail assembly, keeping the cut out
“window” at the front (header) end. Be sure to keep it right side up: the idler
pulley bolt hole above the window is larger on top of the rail than on the
bottom. Slide the front rail onto the assembly; tabs along the side will lock
into place.
10. As a temporary stop, insert a screwdriver into the hole 10" (25 cm) from the
front end of the rail ). Slide the trolley assembly to this point.(Figure 1
11. Lay the new belt beside the rail. Grasp the end with the hooked trolley
connector and pass approximately 12" (30 cm) of belt through the window.
Keeping the ribbed side toward the rail, and allow it to hang while you
complete the next two steps.
12. Replace the idler pulley, lock washer and nut. Rotate it to be sure it spins
freely. Grease the center if necessary.
13. Locate the rail tab. Use a flathead screwdriver and lift the rail tab until the
tab is vertical (90°) . (Figure 2)
14. Pull the belt around the idler pulley and hook the trolley connector into the
retaining slot on the trolley . The ribbed side must contact the (Figure 1)
pulley.
15. With the trolley against the screwdriver, dispense the remainder of the belt
along the rail length toward the motor unit and around the sprocket
(Figure1). The sprocket teeth must engage the belt.
16. Check to make sure the belt is not twisted, then connect it to the flat end of
the trolley threaded shaft with the master link :(Figure 1)
• Push pins of master link bar through holes in end of belt and trolley
threaded shaft.
• Push master link cap over pins and past pin notches.
• Slide clip-on spring over cap and onto pin notches until both pins are
securely locked in place.
WARNING: This product can expose you to chemicals including
lead, which are known to the State of California to cause cancer or
birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
Specyfikacje produktu
| Marka: | Craftsman |
| Kategoria: | Otwieracz do bramy garażowej |
| Model: | CMXZDCG498 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Craftsman CMXZDCG498, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Otwieracz do bramy garażowej Craftsman
30 Września 2024
9 Września 2024
8 Września 2024
1 Września 2024
29 Sierpnia 2024
28 Sierpnia 2024
28 Sierpnia 2024
26 Sierpnia 2024
25 Sierpnia 2024
18 Sierpnia 2024
Instrukcje Otwieracz do bramy garażowej
- Marantec
- LiftMaster
- Skylink
- Einhell
- Entrematic
- Profitech
- Hormann
- Chamberlain
- Univer
- Maveo
- Geba Tronic
- Aperto
- Seculux
- Goris
- DITEC
Najnowsze instrukcje dla Otwieracz do bramy garażowej
14 Stycznia 2025
12 Stycznia 2025
12 Stycznia 2025
11 Stycznia 2025
30 Grudnia 2025
9 Października 2024
30 Września 2024
30 Września 2024
29 Września 2024
28 Września 2024