Instrukcja obsługi Crestron DIN-AP3

Crestron nieskategoryzowany DIN-AP3

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Crestron DIN-AP3 (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 39 osób i została oceniona przez 20 użytkowników na średnio 4.7 gwiazdek

Pobierz PDF

Strona 1/2

DIN-AP3

DIN Rail 3-Series® Automation Processor

Installation and Operations Guide

Hardware Hookup

Make the necessary connections, and apply power after all connections have been made.

NOTE: When making connections to the DIN-AP3, observe the following points:

• Use Crestron power supplies for Crestron equipment.

• The included cable cannot be extended.

Hardware Connections for the DIN-AP3 (Front View)

Description

The Crestron® DIN-AP3 is a 3-Series Control System® automation processor designed for

DIN rail mounting. Featuring the 3-Series control engine, the DIN-AP3 forms the core of

any modern networked home or commercial building, managing and integrating all the

disparate technologies throughout the facility.

Installation

CAUTION: The DIN-AP3 is for indoor use only. Mount in a well-ventilated area. The

ambient temperature must be 32ºF to 104ºF (0ºC to 40ºC). The relative humidity must be

10% to 90% (noncondensing).

CAUTION: To prevent overheating, do not operate this product in an area that exceeds

the environmental temperature range listed on the product web page. Consider using

forced air ventilation to reduce overheating. Also use consideration if installing in a

closed or multiunit rack assembly, since the operating ambient temperature of the

environment may be greater than the room ambient temperature. Contact with thermal

insulating materials should be avoided on all sides of the unit.

NOTES: Observe the following points:

• When installing the DIN-AP3 in an enclosure, group high-voltage devices separately

from low-voltage devices.

• Install and use the DIN-AP3 in accordance with appropriate electrical codes and

regulations.

• A licensed electrician must install the DIN-AP3.

NOTE: Before using the DIN-AP3, ensure the device is using the latest rmware. Check

for the latest rmware for the DIN-AP3 at www.crestron.com/rmware. Firmware is

loaded onto the device using Crestron Toolbox™ software.

Preparing and Connecting Wires

When making the connections, strip the ends of the wires approximately 7/16 in (11 mm).

Use care to avoid nicking the conductors. Tighten the connector to 5 in-lb

(0.5 to 0.6 N-m). The wire gauge should be 14 to 26 AWG.

Installing the DIN-AP3

The DIN-AP3 should be used in a well-ventilated area. The venting holes should not be

obstructed under any circumstances.

The DIN-AP3 is designed for installation on a DIN rail. Refer to the diagram when installing.

Installing the DIN-AP3

Additional Resources

Visit the product page on the Crestron website (www.crestron.com)

for additional information and the latest rmware updates. Use a QR

reader application on your mobile device to scan the QR image.

I/O (G, 8—1):

To Controllable Devices

From Device Outputs (Contact

Closure or Relay Closure)

RELAY (1—4):

To Controllable

Devices

IR/SERIAL (1—4):

To IRP2 or Serial

Devices

COMPUTER:

To Computer Console

COM (1—2):

To RS-232/422/485

Devices

NET (24 Y Z G):

To Any Cresnet® Network Device

Hardware Connections for the DIN-AP3 (Bottom View)

LAN:

10Base-T/100Base-Tx

Ethernet to LAN

Hardware Connections for the DIN-AP3 (Top View)

Memory:

For SD Card

NOTE: Ensure the unit is properly grounded by connecting the chassis ground lug to an

earth ground (building steel).

NOTE: To prevent overheating, do not operate this product in an area that exceeds the

environmental temperature range stated earlier.

Install the DIN-AP3:

1. Use a at object (e.g., a at-head screwdriver) to pull the DIN rail release downward.

2. Place the top of the DIN-AP3’s rail mount over the top of the DIN rail.

3. Tilt the bottom of the DIN-AP3 toward the DIN rail until it snaps into place

NOTE: When mounting DIN rail products, it may be necessary to use a at-head

screwdriver to pull the DIN rail release tab while snapping the device onto the DIN

rail.

To remove the DIN-AP3 from the DIN rail, use a small, at object (e.g., a at-head

screwdriver) to pull the DIN rail release, and tilt the bottom of the DIN-AP3 away from the

DIN rail.

NOTE: Certain third-party DIN cabinets provide space for an informational label between

each DIN rail row. Crestron’s Engraver software (version 4.0 or later) can generate

appropriate labels for all Crestron DIN rail products.

Congure the Control System

The control system can be congured using Crestron Toolbox or the built-in, web-based

setup tool.

Crestron Toolbox

Use Crestron Toolbox to establish communication and congure the control system. For

details, refer to the Crestron Toolbox help le.

Web-Based Setup Tool

1. Use Crestron Toolbox to set the time zone. For details, refer to the Crestron Toolbox

help le.

2. Use the Internet Explorer® web browser to navigate to http://xxx.xx.xx.xxx/setup

where xxx.xx.xx.xxx is the IP address of the control system. The control system’s

welcome screen is displayed.

NOTE: The web-based setup tool is accessible only from Internet Explorer.

NOTE: If a security warning is displayed, click Install to continue.

3. Click Setup to display the DIN-AP3 setup menu. The DIN-AP3 setup menu displays

the IP address, hostname, and MAC address of the device. It also allows access to

various setup and programming screens.

4. From the DIN-AP3’s setup menu, click the following options to congure the control

system:

• Ethernet Setup congures the DIN-AP3’s Ethernet settings and displays DHCP,

hostname, IP address, subnet mask, default router, domain, and MAC address

settings. In the Ethernet setup menu, there are additional options:

• Click Advanced Settings to specify DNS servers, web server settings, and

SSL settings.

• Click MyCrestron Dynamic DNS to congure the myCrestron.com Dynamic

DNS service.

• Click Ethernet Diagnostics to test the Ethernet communications.

• Click Reboot to reboot the DIN-AP3.

• selects programs to be loaded on startup and controls which Application Setup

program(s) are running.

• congures the COM ports, operates the relays, and Input/Output Control

monitors the Versiports.

• displays information about the connected devices, hardware Diagnostics

conguration, and error logs.

• About displays rmware information.

Click to return to the previous screen.

Specyfikacje produktu

Marka:	Crestron
Kategoria:	nieskategoryzowany
Model:	DIN-AP3
Napięcie wejściowe AC:	24 V
Wysokość produktu:	95 mm
Szerokość produktu:	160 mm
Głębokość produktu:	59 mm
Waga produktu:	277 g
Pojemność pamięci wewnętrznej:	4 GB
Prędkość transferu danych przez Ethernet LAN:	10, 100 Mbit/s
Ilość portów Ethernet LAN (RJ-45):	1
Zakres temperatur (eksploatacja):	0 - 40 °C
Zakres wilgotności względnej:	10 - 90 %
Typ pamięci wewnętrznej:	DDR3 SDRAM
Pamięć wewnętrzna:	0.256 GB
Port RS-232:	2
Technologia okablowania:	10/100Base-T(X)
Rodzaj interfejsu sieci Ethernet:	Fast Ethernet
Typ nośników pamięci:	Flash
Emisja ciepła:	26 BTU/h