Instrukcja obsługi Crestron Essence IW5-W-T
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Crestron Essence IW5-W-T (2 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 25 osób i została oceniona przez 13 użytkowników na średnio 4.2 gwiazdek
Strona 1/2
Essence™ In-Wall Speakers
quickstart guide
IW5, IW6, IW8
www.crestron.com
Specifications subject to
change without notice.
IW5, IW6, IW8
Mount/Remove Speakers
The in-wall speakers include six toggle clamps that simplify the mounting process. If the
grilles are mounted on the speakers, remove them before proceeding. (Refer to “Install/
Remove Grilles”, below.)
1. Connect the speaker cable wires to the spring terminals by pressing the top of the
terminals down and inserting the exposed strands into the hole. Make sure that the
+ + – – wires go to the (red coded) terminals, and the wires go to the (black coded)
terminals.
2. With the toggle clamps turned inward, insert the speaker into the opening. As the six
screws on the front of the speaker are tightened, the toggle clamps first rotate into
clamping position (refer to the figure to the right) and then begin holding the speaker
to the wall. Tighten the screws until the speaker is secured; do not overtighten.
3. Speaker removal is accomplished by reversing the procedures given in steps 1 and 2
above.
a. Loosen the front screws to unclamp the speaker. Continue to loosen the screws
until the toggle clamps rotate inward.
b. When the speaker is loose, carefully remove it from the opening.
c. Disconnect the wires from the terminals.
Install/Remove Grilles
The zero-bezel frameless grilles are held in place by powerful magnets. To remove the
grilles, grip the edges and pull away from the speaker.
1
1Installation
The product of expert Crestron® audio engineering,
Essence™ speakers deliver the pinnacle of performance
for demanding residential installations. Select esoteric
materials, top shelf components and a refined, high-end
appearance underscore the meticulous design behind
each model. The result is a complete line of in-wall and
in-ceiling speakers worthy of a place in every room of
the finest custom home.
QUICKSTART DOC. 7394B (2034614) 12.12
Determine Placement In Room
Rear View (Typical)
Install Cables
Run the cables from the audio source to each speaker location following all appropriate
local codes. Strip the ends of the speaker cable wires 1/4” to 1/2” (6 mm to 12 mm) and
twist the exposed strands.
Spring
Terminals (2)
Toggle
Clamps (6)
Tighten
Screws
The Essence line promises the ultimate in installed audio
design, delivering simply stunning sound quality while
minimizing any impact on your décor thanks to paintable
zero-bezel grilles.
Speaker placement is largely a matter of personal preference. However, placing the speaker
near a corner will extend its low frequency response.
Prepare Mounting Holes
Before finalizing the speaker location, check to make sure there are no fixtures, pipes, air
ducts, joists, or other possible obstructions. Use a good quality stud finder to locate joists.
If there is no access to the area behind the wall, and it is uncertain that there are no
obstructions, carefully drill a small hole just through the wall near the middle of the proposed
speaker location(s) and use one of the commercially available inspection devices designed for
this purpose, or do one of the following:
● Use a piece of stiff wire, bent into an “L” shape, with one end long enough to explore an
area equal to the size of the speaker with the toggle clamps extended. Insert the wire into
the hole, make sure it rotates freely in a complete circle and that there is sufficient depth,
or
● Use a drywall saw to cut a small hole at a 45° angle toward the inside of the hole. An
angle cut simplifies repair since the removed piece can be reinserted to help plug the hole.
90°
If there are no obstructions, use the supplied template to trace outlines of the mounting holes
on the wall. Cut the final mounting holes at a 90° angle to the wall.
Paint the Speaker Grilles
Speaker grille painting should be done prior to mounting.
1. Carefully remove the material on the underside of the grilles and set them aside for
reinstallation. It may be necessary to use a knife or other sharp instrument to free
an edge of the material so it can be peeled away. Use care to avoid cutting or
tearing the material.
2. Dry brush or lightly spray the surface to be painted. Use care to avoid clogging the
holes in the grilles.
3. Once the paint is dry, reinstall the material to the underside.
Front View (Typical)
45°
Specyfikacje produktu
| Marka: | Crestron |
| Kategoria: | głośnik |
| Model: | Essence IW5-W-T |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Crestron Essence IW5-W-T, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje głośnik Crestron
7 Kwietnia 2025
7 Kwietnia 2025
7 Kwietnia 2025
30 Września 2024
30 Września 2024
30 Września 2024
27 Września 2024
27 Września 2024
26 Września 2024
24 Września 2024
Instrukcje głośnik
- Jamo
- One Acoustics
- Avantree
- Audiotec Fischer
- Argon
- Medion
- JVC
- Eufy
- Telestar
- Punos
- Art Sound
- Turbosound
- Dual
- Kinyo
- Roadstar
Najnowsze instrukcje dla głośnik
8 Kwietnia 2025
8 Kwietnia 2025
8 Kwietnia 2025
5 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025