Instrukcja obsługi Crestron GLS-PART-CN
Crestron
inteligentny dom
GLS-PART-CN
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Crestron GLS-PART-CN (2 stron) w kategorii inteligentny dom. Ta instrukcja była pomocna dla 38 osób i została oceniona przez 19.5 użytkowników na średnio 3.6 gwiazdek
Strona 1/2
GLS-PART-CN
Cresnet® Partition Sensor
Installation and Operation Guide
Description
The Crestron® GLS-PART-CN is a partition sensor that is controlled by the Cresnet
®
network and designed for installation into a 1-gang electrical box or surface mounting. The
GLS-PART-CN has a contact closure output (EXT) that allows for use in a non-system
environment.
Installation
NOTE: Observe the following points:
• Install and use this product in accordance with appropriate electrical codes and
regulations.
• If you are unsure about any part of these instructions, consult a qualied electrician.
• Sensors must be mounted on a vibration-free surface.
NOTE: Before using the GLS-PART-CN, ensure the device is using the latest rmware.
Check for the latest rmware for the GLS-PART-CN at www.crestron.com/rmware.
Load the rmware onto the device using Crestron Toolbox™ software.
Preparing and Connecting Wires
When making connections, strip the ends of the wires approximately 7/16 in (11 mm). Use
care to avoid nicking the conductors. Tighten the connector to 5 in-lb (0.5 to 0.6 Nm). The
wire gauge should be 14 to 26 AWG.
Wiring the GLS-PART-CN
The 5-pin terminal block connects the GLS-PART-CN to the Cresnet network (24 Y Z G)
and to a non-system device (EXT).
Wire the GLS-PART-CN
Additional Resources
Visit the product page on the Crestron website (www.crestron.com)
for additional information and the latest rmware updates. Use a QR
reader application on your mobile device to scan the QR image.
Standard 1-gang
electrical box
Ceiling
Mounting
screws (2)
Faceplate
(Not included)
3. Attach the desired decorator style faceplate (not supplied).
GLS-PART-CN Installed in a 1-Gang Electrical Box with Faceplate
4. Turn the Cresnet system power on.
Surface Mount the GLS-PART-CN
After the Cresnet network wiring has been installed and veried, use the following
procedure to surface mount the GLS-PART-CN.
1. Remove the two screws from the back of the GLS-PART-CN and then remove the
bracket. Retain the screws.
Remove these two screws in order to swap the mounting
brackets. Reuse the screws for reassembly using the
other mounting bracket.
Connection to the
control system Contact closure output for
non-system environment
Ceiling Mount in 1-Gang Electrical Box
After the Cresnet network wiring has been installed and veried, use the following
procedure to install the device in a standard 1-gang electrical box.
1. Holding the GLS-PART-CN with the sensors facing the area to be monitored, place
the GLS-PART-CN into the electrical box.
2. Secure the GLS-PART-CN using the included screws.
Installing the GLS-PART-CN in a 1-Gang Electrical Box
Mounting Location
Position the GLS-PART-CN 2 ft (0.6 m) away from the partition. The GLS-PART-CN
sensors must face the partition so that when the partition opens, the sensor sees the
unobstructed room.
Sensor Mounting Location (Bottom View)
2 ft (0.6 m)
Partition
Specyfikacje produktu
| Marka: | Crestron |
| Kategoria: | inteligentny dom |
| Model: | GLS-PART-CN |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Crestron GLS-PART-CN, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje inteligentny dom Crestron
21 Września 2024
4 Czerwca 2024
4 Czerwca 2024
4 Czerwca 2024
4 Czerwca 2024
4 Czerwca 2024
4 Czerwca 2024
Instrukcje inteligentny dom
- KanexPro
- AirLive
- LSC Smart Connect - Action
- Easy Home
- Byron
- Tenda
- Osram
- Cisco
- Netgear
- Swann
- Popp
- KKT Kolbe
- Hager
- Winland
- Imou
Najnowsze instrukcje dla inteligentny dom
29 Marca 2025
29 Marca 2025
29 Marca 2025
27 Marca 2025
18 Marca 2025
18 Marca 2025
12 Marca 2025
25 Lutego 2025
19 Lutego 2025
14 Lutego 2025