Instrukcja obsługi Crestron TST-902

Crestron nieskategoryzowany TST-902

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Crestron TST-902 (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 27 osób i została oceniona przez 14 użytkowników na średnio 4.0 gwiazdek

Pobierz PDF

Strona 1/2

quickstart guide

Touch Screen RF Roaming

www.crestron.com

Specifications subject to

change without notice.

Touch Screen RF Roaming

QUICKSTART DOC. 7671B (2044362) 01.16

Several Crestron touch screens can be used with multiple Extended Range (ER) Wireless

Gateways (sold separately) to create a wireless roaming network.

Begin by accessing the setup screens on the device.

Get Started

A. Enable Roaming on the Touch Screen

NOTE: This document applies to Crestron

® touch screens with roaming capability, such as the

TSR-302, TST-600, TST-602, and TST-902. The screens shown here are from the TST-602. The

composition of the screens may vary between products, but the basic controls called out in this

document are the same on all of them.

From the device’s main setup screen, tap to display the screen.RF Setup RF Setup

2Enable Roaming

B. Enable Roaming on the Gateway

To enable roaming on the gateway, use the following procedure:

1. Open a text console for the gateway using the gateway’s IP address.

2. Enter the command .rfroaming on

3. Enter the command .reboot

This procedure must be performed for each gateway used in the roaming setup.

NOTE: By default, roaming is disabled in both the touch screen and the gateway, and must

be enabled in both devices.

On the screen, tap under to enable the button.RF Setup On RF Roaming Roaming Setup

PROGRAMMING TIP: When an RF touch screen is progammed for connection to multiple RF

gateways using roaming, the RF touch screen must be defined at the assigned RF ID on each

gateway. Programming should be connected identically to each gateway so that the RF touch

screen behaves identically no matter which RF gateway it happens to be connected to at that

time.

quickstart guide

Touch Screen RF Roaming

www.crestron.com

Specifications subject to

change without notice.

Touch Screen RF Roaming

QUICKSTART DOC. 7671B (2044362) 01.16

3Roaming Setup

B. View Gateway UID

Selected Gateway’s UID on the right side of the screen indicates the currently selected

gateway’s UID.

Tap See All GW UID to see the UIDs of all acquired gateways.

The specific patents that cover Crestron products are listed at patents.crestron.com.

Certain Crestron products contain open source software. For specific information, please visit

www.crestron.com/opensource.

Crestron and the Crestron logo are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United

States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document

to refer to either the entities claiming the marks and names or their products. Crestron disclaims proprietary interest in the

marks and names of others. Crestron is not responsible for errors in typography or photography.

This document was written by the Technical Publications department at Crestron.

On the screen, tap to display the screen.RF Setup Roaming Setup Roaming Setup A. Acquire Gateways

Up to eight gateways can be acquired by a touch screen. To acquire multiple gateways, put all

the gateways in Acquire mode. Then, use the following procedure:

1. Select the appropriate gateway index by tapping one of the buttons marked through GW 1

on the screen.GW 8 Roaming Setup

2. Tap ACQUIRE START. The Acquire State box on the screen will display an “Acquire in

progress” message. When the acquire is complete, the message will say “Acquire OK.”

3. Repeat steps 1 and 2 until all gateways are acquired.

If multiple touch screens are used, follow the steps above for each touch screen.

NOTE: When multiple gateways are put in Acquire mode at the same time, the touch screen will

save the first available gateway in the selected gateway index. To save gateways in a particular

order on the list, put only one gateway in Acquire mode at a time and perform the acquire

process, selecting the required gateway index. Gateways that are already acquired are not

acquired again, unless first removed from the list, as shown in part C.

C. Remove a Gateway

To remove an acquired gateway from the list, select the appropriate index for the gateway

( though ) and tap . A “CONFIRM GATEWAY REMOVE” GW 1 GW 8 Remove Selected GW

message appears. Tap Yes Remove to remove the gateway, or to cancel.No

Specyfikacje produktu

Marka:	Crestron
Kategoria:	nieskategoryzowany
Model:	TST-902
Kolor produktu:	Czarny
Typ wyświetlacza:	TFT
Wysokość produktu:	164 mm
Szerokość produktu:	264 mm
Głębokość produktu:	19 mm
Waga produktu:	808 g
Wbudowane głośniki:	Tak
Długość przekątnej ekranu:	8.7 "
Pojemność pamięci wewnętrznej:	1000 MB
Zakres temperatur (eksploatacja):	0 - 45 °C
Zakres wilgotności względnej:	10 - 90 %
Rozdzielczość:	1008 x 588 px
Obsługiwane formaty audio:	MP3
Pobór mocy:	7 W
Lokalizacja zasilania:	Zewnętrzny
Typ podświetlacza:	LED
Jasność:	300 cd/m²
Napięcie wyjściowe adaptera AC:	24 V
Głębia kolorów:	24 bit
Technologia touchscreen:	Pojemnościowa
Współczynnik kontrastu:	700:1