Instrukcja obsługi Ctek CT5 Powersport
Ctek
Ładowarka baterii
CT5 Powersport
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ctek CT5 Powersport (7 stron) w kategorii Ładowarka baterii. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 6 użytkowników na średnio 4.5 gwiazdek
Strona 1/7
EN
EN • 3
MANUAL
CONGRATULATIONS
to the purchase of your new professional switch mode battery charger. This charger is
included in a series of professional chargers from CTEK SWEDEN AB and represents the
latest technology in battery charging.
Read safety instruction
HOW TO CHARGE
1. Connect the charger to the battery.
For batteries mounted inside a vehicle
1. Connect the charger according to the
vehicles manual.
2. Connect the charger to the wall socket.
3. Disconnect the charger from the wall socket
before disconnecting the battery.
4. Disconnect the black clamp before the red
clamp.
1 2
2. Connect the charger to the wall socket. The power lamp will indicate that the mains
cable is connected to the wall socket. The power lamp will blink if the battery clamps
are incorrectly connected. The reverse polarity protection will ensure that the battery or
charger will not be damaged.
RECOND LITHIUMNORMAL
NORMAL
BAT T ERY
PROG RA M
ERROR LAMP
RECOND
OPT ION
FULLY CHARGED
LITHIUM
BAT T ERY
PROG RA M
POWER LAMP
MODE BUT T ON
3. Press the MODE-button to select charging program.
NORMAL BATTERY PROGRAM LITHIUM BATTERY PROGRAM
Continue to press the MODE-button to combine charging program with charging options.
RECOND OPTION
Press the MODE-button several times until the desired combination of charging program
and options are lit.
4. Follow the display through the charging process.
The battery is fully charged when the CARE lamp is lit.
5. Stop charging at any time by disconnecting the mains cable from the wall socket.
4 • EN
CHARGING PROGRAMS
Settings are made by pressing the MODE-button. After about two seconds the charger acti-
vates the selected program. The selected program will be restarted next time the charger
is connected.
The table explains the different Charging Programs:
Program Explanation
Normal battery program 14.4V/2.3A
Only for lead-acid batteries.
Recond option 15.8V/0.9A
Use to restore capacity to WET and Ca/Ca batteries. Recond your
battery once per year and after deep discharge to maximise lifetime and
capacity.
READY TO USE
The table shows the estimated time for empty battery to 80% charge.
BATTERY SIZE (Ah) TIME TO 80% CHARGED
5Ah 2h
10Ah 4h
15Ah 6h
20Ah 7h
25Ah 9h
POWER LAMP
If the power lamp is lit with a:
1. STEADY LIGHT
The mains cable is connected to the wall socket.
2. FLASHING LIGHT
The charger has entered the energy save mode. This happens if the
charger can’t detect a battery in 2 minutes.
ERROR LAMP
If the error lamp is lit, check the following:
1. Polarity error: Is the charger’s positive lead connected to
the positive charging point?Is the charger’s negative lead
connected to the negative charging point?
2. Is the charger connected to a 12V battery?
3. Has charging been interrupted in STEP 1, 2 or 5?
Restart the charger by pressing the MODE-button. If charging is still
being interrupted, the battery...
CHECK: ...is seriously sulphated and can not accept charge. The
battery may need to be replaced.
CARE: ...can not keep charge. The battery may need to be replaced.
LEAD-ACID
EN
EN • 5
STEP 1 DESULPHATION
Detects sulphated batteries. Pulsing current and voltage, removes sulphate from the lead
plates of the battery restoring the battery capacity.
STEP 2 SOFT START
Tests if the battery can accept charge. This step prevents that charging proceeds with a
defect battery.
STEP 3 BULK
Charging with maximum current until approximately 80% battery capacity.
STEP 4 ABSORPTION
Charging with declining current to maximize up to 100% battery capacity.
STEP 5 ANALYZE
Tests if the battery can hold charge. Batteries that can not hold charge may need to be
replaced.
STEP 6 RECOND
Choose the Recond program to add the Recond step to the charging process. During the
Recond step voltage increases to create controlled gassing in the battery. Gassing mixes
the battery acid and gives back energy to the battery.
STEP 7 FLOAT
Maintaining the battery voltage at maximum level by providing a constant voltage charge.
STEP 8 PULSE
Maintaining the battery at 95–100% capacity. The charger monitors the battery voltage
and gives a pulse when necessary to keep the battery fully charged.
12345678
15.8V 2.3A until 12.6V Increasing voltage to
14.4V. 2.3A
Declining current
14.4V
Voltage limit 12V 13.6V
2.3A
12.7V–14.4V
2.3A–1.0A
Max 15.8V
0.9A
Time limit: Max 4h Max 20h 16h 3 minutes 2h or 6h 10 days Max 1h pulse.
Auto pulse every 24h
LEAD-ACID
Specyfikacje produktu
| Marka: | Ctek |
| Kategoria: | Ładowarka baterii |
| Model: | CT5 Powersport |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Ctek CT5 Powersport, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Ładowarka baterii Ctek
4 Października 2024
25 Września 2024
25 Września 2024
25 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
Instrukcje Ładowarka baterii
- Ładowarka baterii MIDAC
- Ładowarka baterii Audio-Technica
- Ładowarka baterii Outspot
- Ładowarka baterii SilverCrest
- Ładowarka baterii Defort
- Ładowarka baterii Amprobe
- Ładowarka baterii Horizon
- Ładowarka baterii Ozito
- Ładowarka baterii Monster
- Ładowarka baterii Enersys
- Ładowarka baterii EVBox
- Ładowarka baterii Westfalia
- Ładowarka baterii Bury
- Ładowarka baterii Cobra
- Ładowarka baterii Tycon Systems
Najnowsze instrukcje dla Ładowarka baterii
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
28 Stycznia 2025
28 Stycznia 2025
28 Stycznia 2025
28 Stycznia 2025
28 Stycznia 2025
17 Stycznia 2025
13 Stycznia 2025