Instrukcja obsługi Ctek D250TS
Ctek
Ładowarka baterii
D250TS
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ctek D250TS (7 stron) w kategorii Ładowarka baterii. Ta instrukcja była pomocna dla 22 osób i została oceniona przez 11.5 użytkowników na średnio 4.7 gwiazdek
Strona 1/7
EN
EN • 3
MANUAL
CONGRATULATIONS
Congratulations on purchasing your new CTEK professional 24V DC/DC switch mode battery
charger, 12V converter and battery equalizer. This charger is part of a range of professional bat-
tery chargers from CTEK SWEDEN AB. It represents the latest technology in battery charging with
charging and analysis in 4 steps with temperature compensation.
Read this User Manual and follow the instructions carefully before using your new charger.
SAFETY
• The charger is designed for 24V lead-acid batteries mounted into vehicles.
Do not use the charger for any other purpose
• Use safety glasses when connecting or disconnecting a battery.
• Battery acid is corrosive. Rinse immediately with water if acid comes into contact with skin
or eyes. Seek medical advice.
• Make sure that the cables are not being pinched or in contact with warm surfaces
or sharp edges.
• While charging, a battery can emit explosive gases, avoid sparks in the immediate area.
• Always provide for proper ventilation during charging.
• Avoid covering the charger.
Starter Battery
24V+
Service Battery
24V+
Service ground Service Battery Midpoint
D250TS
The D250TS has one 24V input and two alternating outputs. One output charge a 24V
battery and the other provides 50% of the input voltage to the midpoint of a 24V system. This
enables connection of 12V consumers to the battery string and also equalizing this battery
string, for longer battery life.
D250TS
FEATURES:
• Multi-step10A temperature compensated battery charging and battery maintenance.
• Battery separation of Starter and Service batteries.
• Equalization of Service batteries
• Makes connection of 12V consumers directly to 24V Service battery possible.
• When the charger is correctly connected the charger will output 24V on the status signal wire.
Connection of a 24V lamp (max 2W) to the status signal wire will indicate a correctly con-
nected charger.
• The charger will maintain the starter battery untill the supply is below 14V. To avoid draining the
service battery always connect a charger to the service battery when the vehicle is not used for
a longer period.
+IN +OUT
EQU
D250TS
Status signal wire
Temperature sensor
20015884C D250TS, Manual, Print file 002.indd 3 2011-12-20 13:27:12
4 • EN
INSTALLATION OF UNIT
1. Attach the temperature sensor holder on a flat surface on one Starter battery. Position it as close
as possible to a positive post.
2. Use the included drill template. Wiring is simplified if the units are installed according to the drill
template, but other setups are possible.
3. Install the unit(s) on a flat surface where it can be properly fixed and where the unit is not
exposed to fuels, oils or splashes of dirt.
4. Mount the unit with screws intended for the surface and attach it with one screw in each of the
four holes in the corners of the unit. See picture 1. Mount the unit with M4 or ST4.2 screws. The
required torque depends on the surface for mounting.
Figure 1
2Nm
DRILL TEMPLATE
Ø 5mm
168
mm
90,6
mm
Service ground
Service Battery
24V+
Starter Battery
24V+
Status signal wire
Temp sensor
Service Battery Midpoint
20015884C D250TS, Manual, Print file 002.indd 4 2011-12-20 13:27:13
EN
EN • 5
FUNCTIONALITY
The D250TS has three operating modes:
1. 4-step charging of a Starter battery.
2. When Starter battery is fully charged: Equalization of a Service battery on the Input side. This
function provides the possibility to connect 12V consumers to the 1st battery in the Service
battery string.
3. Monitoring. The D250TS now monitors if the Starter battery needs charging (priority) or the
Service battery needs equalization.
B-1 B-2
B-3
IN
GNC A
OUT
c2
c1
DC/DC
24V/1CA
ALTERNATOR
STARTER MOTOR
SERVICE
BATTERY
SERVICE
BATTERY
STARTER
BATTERY
STARTER
BATTERY
20015884C D250TS, Manual, Print file 002.indd 5 2011-12-20 13:27:13
Specyfikacje produktu
| Marka: | Ctek |
| Kategoria: | Ładowarka baterii |
| Model: | D250TS |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Ctek D250TS, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Ładowarka baterii Ctek
4 Października 2024
25 Września 2024
25 Września 2024
25 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
Instrukcje Ładowarka baterii
- Ładowarka baterii Hive
- Ładowarka baterii Venom
- Ładowarka baterii Davis
- Ładowarka baterii Studer
- Ładowarka baterii HTronic
- Ładowarka baterii Soyosource
- Ładowarka baterii Wentronic
- Ładowarka baterii PACO
- Ładowarka baterii Hyundai
- Ładowarka baterii IEB
- Ładowarka baterii Envertech
- Ładowarka baterii Novero
- Ładowarka baterii Yato
- Ładowarka baterii Fuxtec
- Ładowarka baterii Vivanco
Najnowsze instrukcje dla Ładowarka baterii
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
28 Stycznia 2025
28 Stycznia 2025
28 Stycznia 2025
28 Stycznia 2025
28 Stycznia 2025
17 Stycznia 2025
13 Stycznia 2025