Instrukcja obsługi Ditek DTK-UPS800
Ditek
zasilacz UPS
DTK-UPS800
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ditek DTK-UPS800 (2 stron) w kategorii zasilacz UPS. Ta instrukcja była pomocna dla 44 osób i została oceniona przez 22.5 użytkowników na średnio 4.5 gwiazdek
Strona 1/2
Line Interactive UPS
400V VAA-800
Inspection
The following items are inside the box:
● UPS unit ● User manual USB cable●
Remove the and inspect UPS from its package it for damage that
may have occurred during shipping. If any damage is discovered,
re-pack the unit and return it to the place of purchase.
Connect to Utility Power
Connect AC power cord to utility power. he UPS will Tbegin
charging the internal battery s allow the battery to . For best result ,
charge 6 hours prior to initial use.for a minimum of
Connect /Computer Ethernet
This UPS provides surge protection for a single Ethernet
connection. Remove existing Ethernet cable from PC and insert
into UPS “IN” . connector Using an additional Ethernet cable,
insert into PC network adapter and UPS “OUT” connector.
Battery backup outlets
AC input
Fuse/Circuit breaker
USB com. port
Ethernet surge protection
Plug in Equipment
Plug your equipment to Battery Backup Outlets on the rear panel of
the UPS.
NOTE: Make the allsure that UPS is on to protect powered
important from devices data loss power failure. during
CAUTION: NEVER connect a laser printer or scanner to the
battery of UPS. The backup outlets equipment may draw
significantly power to overload UPS. the
Connect USB Cable and Install Software
Connect one end of the other to the USB cable to PC and the USB
port the rear of the UPS. at
Download the latest version of ViewPower software USB from
https://www.diteksurgeprotection.com/ups-software.html to your
hard drive. Follow on-screen instructions to complete the software
installation.
Operation Display
UPS
Mode LCD Description
UPS
Power on
When UPS is powered
on, it will enter this mode
for 4 seconds.
AC Mode
When AVR is
functioning, icon will
flash every second.
LCD information will be
displayed in the following
order when LCD is
touched.
1. Output voltage
2. Input voltage
3. Load level
4. Battery capacity
Overload
in AC
mode icon will flash.
When overload occurs,
alarm will beep every 0.5
second.
Battery
Mode
When battery level is
low, icon will flash.
Alarm will beep every 10
seconds and LCD
information will be
displayed in the following
order when LCD is
touched.
1. Output voltage
2. Input voltage
3. Load level
4. Battery capacity
Overload
in battery
mode icon will flash.
When overload occurs,
alarm will beep every 0.5
second.
NOTE: If shuts off, you thebacklight may it activate by touching
screen.
Fault Code Table:
Fault condition LCD Solutions
Output short
circuited
Disconnect short-circuited loads
and restart the UPS again.
Overload fault Disconnect all output loads and
restart the UPS again.
Overcharge Call for service immediately.
Bad or severely
discharged battery
Please replace the battery.
High output voltage
fault
Call for service immediately.
Over-temperature Turn off the unit and wait for1.
cooling.
2. Or remove excessive loads
and wait for cooling.
If fault alarm occurs, please call for service immediately.
www.diteksurgeprotection.com 1-800-753-2345
INT-100177-001 PN: 191-608 REV 01
Specyfikacje produktu
| Marka: | Ditek |
| Kategoria: | zasilacz UPS |
| Model: | DTK-UPS800 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Ditek DTK-UPS800, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje zasilacz UPS Ditek
2 Czerwca 2024
2 Czerwca 2024
2 Czerwca 2024
2 Czerwca 2024
Instrukcje zasilacz UPS
- Lenovo
- APC
- Tripp Lite
- V7
- FSP
- Online USV
- Sharkoon
- Emerson
- CyberPower
- Eaton
- Adj
- PowerWalker
- Salicru
- Murr Elektronik
- SurgeX
Najnowsze instrukcje dla zasilacz UPS
19 Września 2024
28 Sierpnia 2024
28 Sierpnia 2024
23 Sierpnia 2024
21 Sierpnia 2024
21 Sierpnia 2024
21 Sierpnia 2024
21 Sierpnia 2024
21 Sierpnia 2024
21 Sierpnia 2024