Instrukcja obsługi Draper Clarion
Draper
ekran do rzutników
Clarion
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Draper Clarion (2 stron) w kategorii ekran do rzutników. Ta instrukcja była pomocna dla 37 osób i została oceniona przez 19 użytkowników na średnio 4.4 gwiazdek
Strona 1/2
Assembly/Mounting Instructions
Clarion Permanently Tensioned Projection Screen by Draper
Caution
① Read instructions through completely before proceeding.
② Follow instructions carefully. Installation con trary to instructions
invalidates warranty.
③ When lifting assembled screen, do not lift at only one corner; lift at
both corners. Lifting by one corner could result in damage to the
screen frame, especially on large screens.
④ Screen should be accessible for complete removal should fabric become
damaged or should other ser vice be required.
⑤ Screen should be installed level (using a carpenter’s level).
⑥ Nothing should be fastened to screen frame or viewing surface.
⑦ Make sure you have received all parts (see parts list below and exploded
diagram on page 2).
⑧ Screwdriver required for screen assembly; drill and screwdriver needed
for attachment to wall.
⑨ The ideal temperature range for assembling folding screens to prevent
damaging the surface is 68°-78° F (20°-26° C). Assembling below
recommended temperatures may damage surface and void warranty.
NOTE: Screen has been thoroughly inspected and tested at factory and
found to be operating properly prior to shipment.
Copyright © 2011 Draper Inc. Form Clarion_Inst11 Printed in U.S.A.
®
If you encounter any diffi culties installing or ser vic ing your Clarion screen, call your
dealer or Draper, Inc., Spiceland, Indiana, (765) 987-7999; or fax (765) 987-7142.
Clarion—Hardware and Parts List
Frame Preparation
① Clean area and place frame assembly pieces face down. Snap plastic
corner pieces into ends of aluminum frame extrusions as indicated in
Figures 1 through 4.
Figure 1
② Check to verify that all four (4) plastic corners are seated securely in
aluminum frame extrusion lengths (see Fig. 5). Lock in place using eight (8)
self-tapping screws.
Caution: Do not over-tighten fasteners—over-tightening could caUse
damage to the frame corners.
Figure 2
Frame Extrusions - 4
Frame Corners - 4
Z-Brackets - 2
Viewing Surface - 1
Plastic Tubing - 4
Surface Retention
Extrusions- 4
Front
Back
Self-tapping
Screws-8
Figure 3
Figure 5
Figure 4
(Continued on Page 2)
Patented by Draper, Inc., U.S. Patent Nos. 6,785,047; 7,113,332; and 7,369,310.
Specyfikacje produktu
| Marka: | Draper |
| Kategoria: | ekran do rzutników |
| Model: | Clarion |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Draper Clarion, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje ekran do rzutników Draper
14 Maja 2024
12 Maja 2024
6 Maja 2024
6 Maja 2024
5 Maja 2024
5 Maja 2024
Instrukcje ekran do rzutników
Najnowsze instrukcje dla ekran do rzutników
2 Sierpnia 2024
2 Sierpnia 2024
28 Lipca 2024
30 Maja 2024
30 Maja 2024
30 Maja 2024
30 Maja 2024
23 Maja 2024
23 Maja 2024
15 Maja 2024