Instrukcja obsługi Elektrobock Pocket Home PH-SP2
Elektrobock
odbiornik
Pocket Home PH-SP2
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Elektrobock Pocket Home PH-SP2 (4 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 16 osób i została oceniona przez 8.5 użytkowników na średnio 4.3 gwiazdek
Strona 1/4
Version 11.02
Wireless receiver for control of
electric heating devices
- WALL-MOUNTED -
PH-SP2
Operating instructions
Control of electric heating systems
Component of the PocketHome
®system
Two-way radio communication at 433,92 MHz
The connected electric appliance is switched according to
the required temperature
The control unit PH-BSP is the pilot component
The device can only be installed by a person with adequate qualification!
The installation must be executed in a voltage-free state!
holes for
installation
on KU/KP68
Fig.1 Fig.2 Fig.3
230 V/ 50 Hz
Wiring diagram:
L
N
FUNCTION BUTTON:
SHORT PRESSING - coding.
LONG PRESSING (for about 5 s) - RESET
deleting the code from the memory (the green and
red LEDs flash simultaneously).
max.
16 A
Fig.4
INSTALLATION
output terminals
power supply
terminals
FUNCTION
BUTTON
PH-SP2 is used for switching the heating device in connection
with the PH-BSP control unit.
ACTIVATION PROCEDURE
1. Lift off the front cover of the receiver acc. to Fig. 1, 2.
2. Attach the receiver to the wall (or to the wiring box directly).
3. Switch off the main circuit breaker.
4. Connect the receiver acc. to the diagram.
5. Connect the receiver to the mains 230 V / 50 Hz.
6. Switch on the main circuit breaker; the green diode flashes
on the receiver; thus the receiver is ready for further setting.
7. Shortly press the FUNCTION BUTTON
for about 1.5 s (the green and red
diode are flashing alternately).
8. On the PH-BSP control unit, press the” Test ”
button in the ACTIV mode to activate the
SP switching components (see page 10 of
the PH-BSP instructions).
9. If the code has been learned correctly,
the green and red diodes flash
simultaneously.
INDICATION DIODES
LED 2LED 1
empty memory, code not learned
code learned
FLASHING ALTERNATELY= code learning mode
FLASHING SIMULTANEOUSLY= code has been learned
SIMULTANEOUS LONG FLASH= code was ERASED
relay switched
ERROR (if no signal is received from the
transmitter within approx. 6 hours, it switches to
the 2-min-ON / 8-min-OFF mode). LED flashes
only if the relay is on, i.e. for 2 minutes.
EXPLANATION: LIT UNLIT FLASHING
FUNCTION
Specyfikacje produktu
| Marka: | Elektrobock |
| Kategoria: | odbiornik |
| Model: | Pocket Home PH-SP2 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Elektrobock Pocket Home PH-SP2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje odbiornik Elektrobock
30 Grudnia 2025
16 Września 2024
8 Września 2024
5 Września 2024
5 Września 2024
31 Sierpnia 2024
26 Sierpnia 2024
20 Sierpnia 2024
Instrukcje odbiornik
- odbiornik Kramer
- odbiornik Alto
- odbiornik Kogan
- odbiornik Williams Sound
- odbiornik Onkyo
- odbiornik Strong
- odbiornik SilverCrest
- odbiornik Kemo
- odbiornik Roland
- odbiornik NAD
- odbiornik AudioSource
- odbiornik Bose
- odbiornik Mx Onda
- odbiornik SureCall
- odbiornik Focal
Najnowsze instrukcje dla odbiornik
9 Kwietnia 2025
9 Kwietnia 2025
5 Kwietnia 2025
4 Kwietnia 2025
3 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
1 Kwietnia 2025
30 Marca 2025
30 Marca 2025