Instrukcja obsługi Elica Vavano EVV648S1
Elica
Okap wyciągowy
Vavano EVV648S1
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Elica Vavano EVV648S1 (27 stron) w kategorii Okap wyciągowy. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 4 użytkowników na średnio 4.5 gwiazdek
Strona 1/27
Use, Care, and
Installation Guide
Guide
d’utilisation,
d’entretien et
d’installation
Guía de
instalación, uso y
mantenimiento
READ AND SAVE THESE
INSTRUCTIONS
LISEZ CES
INSTRUCTIONS ET
CONSERVEZ-LES
LEA Y CONSERVE
ESTAS INSTRUCCIONES
LIB0152213
Printed in Mexico
10/18
Models: KIT0154387
2
ENGLISH
Contents
Important safety notice................................................................................................................................................................................................. 3
Installation Requirements ................................................................................................. ........................................................................................... 4
Tools & Parts ................................................................................................................................................................................................................ 4
Location Requirements ........................................................................................................................................................................................... 5
Product Dimension ................................................................................................................................................................................................... 5
Venting Requirements ............................................................................................................................................................................................. 5
Electrical Requirements .......................................................................................................................................................................................... 6
Installation Instructions ................................................................................................................................................................................................ 6
Prepare the location ................................................................................................................................................................................................ 6
Install In-Blower System .......................................................................................................................................................................................... 9
Make electrical connection for the In-Line Blower System...................................................................................................................... 10
Make electrical between the In-Line Blower System and Range Hood .............................................................................................. 11
Warranty ........................................................................................................................................................................................................................... 14
Wiring Diagram .............................................................................................................................................................................................................. 43
APPROVED FOR RESIDENTIAL APPLIANCES
FOR RESIDENTIAL USE ONLY
READ AND SAVE THESE INSTRUCTIONS
PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.
INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.
IMPORTANT: Save these Instructions for the Local Electrical Inspector’s use.
INSTALLER: Please leave these Instructions with this unit for the owner.
OWNER: Please retain these instructions for future reference.
Safety Warning: Turn o power circuit at service panel and lock out panel, before wiring this appliance.
Requirement: 120 V AC, 60 Hz. 15 or 20 A Branch Circuit.
8
3 Remove the motor mounting plate by setting free the
spring clip. NOTE: The spring clip should be outside the
slot in the mounting plate.
A. Mounting plate
B. Spring Clip
A
B
A. Mounting plate
B. Spring Clip
A
B
4 Run out the power supply wires and connector through
the hole in the right end of the motor mounting plate.
5 Slide out the left mounting plate from under the motor
mounting bracket.
A
B
A. Motor mounting plate
B. Motor mounting bracket
6 Install the grease filters.
Prepare for Mounting the In-Line Blower System
The In-Line Blower System must be fastened to a secure
structure of the roof, ceiling, wall, floor, or new or existing
frame construction. The 4 holes on either the inlet (bottom)
side or the outlet (top) side of the blower must be used to
mount the in-line blower system to the structure.
NOTE: The mounting hole locations must span the studs.
Additional stud framing may be required. Plywood may be
used to span open areas between ceiling joists or roof rafters
to aid installation. This structure must be strong enough to
support the weight of the in-line blower system (50 lb [22.6
kg] min).
Prepare the In-line Blower System
I WARNING
Excessive Weight Hazard
Use two or more people to move and install range hood.
Failure to do so can result in back or other injury.
1 Disconnect power.
2 Determine which venting method to use: roof or wall
exhaust.
3 Using two or more people, move the in-line blower motor
system to the mounting location.
4 Remove the 10 screws from the front cover of the in-line
blower motor housing and set them aside.
5 Remove the front cover of the in-line blower motor
housing and set it aside.
NOTE: To make the in-line blower motor housing easier to
mount, the blower motor assembly can be removed.
6 Disconnect the motor electrical plug from the blower
motor assembly.
7 Remove the screws that secure the blower motor
assembly to the in-line blower housing and set them aside.
8 Pull the spring clip to release the blower motor assembly.
Remove the blower motor assembly from the housing and
place it on a covered surface.
A
BC
D
A. Front cover
B. Blower mounting
screws
C. Spring clip
D. Motor electrical
plug
Specyfikacje produktu
| Marka: | Elica |
| Kategoria: | Okap wyciągowy |
| Model: | Vavano EVV648S1 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Elica Vavano EVV648S1, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Okap wyciągowy Elica
5 Kwietnia 2025
30 Marca 2025
30 Marca 2025
27 Stycznia 2025
27 Stycznia 2025
15 Stycznia 2025
8 Października 2024
8 Października 2024
8 Października 2024
7 Października 2024
Instrukcje Okap wyciągowy
- Okap wyciągowy Condor
- Okap wyciągowy German Pool
- Okap wyciągowy Continental Edison
- Okap wyciągowy Aspes
- Okap wyciągowy Blomberg
- Okap wyciągowy Amica
- Okap wyciągowy Classique
- Okap wyciągowy Indesit
- Okap wyciągowy Privileg
- Okap wyciągowy Weller
- Okap wyciągowy Itho
- Okap wyciągowy Unox
- Okap wyciągowy New World
- Okap wyciągowy Teka
- Okap wyciągowy Panasonic
Najnowsze instrukcje dla Okap wyciągowy
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025