Instrukcja obsługi Emerson 1F83H-21NP

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Emerson 1F83H-21NP (12 stron) w kategorii termostat. Ta instrukcja była pomocna dla 38 osób i została oceniona przez 5 użytkowników na średnio 4.7 gwiazdek

PART NO. 37-7569

1504

1F83H-21NP (Non-Programmable)

Installation and Operating Instructions

80 Series Heat Pump Thermostat

Battery Powered or Hardwired with Common

emersonthermostats.com

white-rodgers.com

Thermostat Applications

Maximum

Stages

Heat /Cool

Single Stage Compressor, Heat Pump

Systems (air source or geothermal) –

1Stage Aux/Emergency Heat

2/1

Thermostat Installation 2-4

Wiring 2

Installer Menu3-4

Using the Thermostat5-6

Thermostat Overview 5

User Menu6

Troubleshooting 7-8

Homeowner Help Line8

INDEX

MERCURY NOTICE:This product does not contain

mercury. However, this product may replace a product

that contains mercury. Mercury and products containing

mercury must not be discarded in household trash.

Refer to www.thermostat-recycle.org for information

on disposing of products containing mercury.

Electrical Rating:

Battery Power to VAC, NEC Class II, Hz .....................................20 3050/60

Input-Hardwire to VAC, NEC Class II, /Hz ....................................20305060

Terminal Load A per terminal, A maximum all terminals combined .......................................... 1.5 2.5

Setpoint Range to F (to ........................................45° 99°7° 37° C)

Rated Dierentials (@ 6°F/ Hr): Fast Med Slow

Heat Pump (Heat)................................ 0.9°F 1.2°F 1.7°F

Heat Pump (Cool) . ................................09°F 1.2°F 1.7°F

Auxiliary Heat . ...................................... 05°F 0.75°F 1.9°F

Operating Ambient .................................. 32°F to +105°F (0° to +41°C)

Display Temperature Range 32°F to +99°F (0 to 37°C) .......................

Operating Humidity % non-condensing maximum .................................90

Shipping Temperature Range ................... °F to + °F-20150 (-29° to +65°C)

Thermostat Dimensions ........................... 3-3/4” H x 6” W x 1-1/8” D

SPECIFICATIONS

Optional Accessory: Wall Cover-up Plate F61-2663, 6 3/4” W x 4 1/2” H

2

Terminal DesignationsTerminal Function

RPower (V) 24

O/B Changeover Terminal-Energized in Cool (O) or Heat (B)

for Heat Pump or Damper Systems

YHeat and Cool Mode 1st Stage Compressor

GFan Relay

E*Auxiliary only Heat Mode (Emergency Heat)

CCommon wire for (optional with batteries)24V

LHeat Pump malfunction / Diagnostic terminal

(input signal requires common)

W*Heat Mode – nd stage2 2

*Cut W2/E jumper when separate heat sources are used for W and E.2

IMPORTANT: For Dual Fuel Heat Pump applications, be sure to turn on the Duel Fuel Logic option

(found in the Installer’s Menu)

WIRING

Refer to equipment manufacturer’s instructions for specic system wiring information. After

wiring, see INSTALLER MENU for proper thermostat conguration. Wiring table shown are

for typical systems and describe the thermostat terminal functions.

THERMOSTAT INSTALLATION

Precautions

• Do not exceed the specication ratings.

• All wiring must conform to local and national electrical codes and ordinances.

• This control is a precision instrument, and should be handled carefully. Rough handing or

distorting components could cause the control to malfunction.

WARNING

!

Do not use on circuits exceeding specied voltage.

Higher voltage will damage control and could

cause shock or re hazard.

Do not short out terminals on gas valve or primary

control to test. Short or incorrect wiring will burn

out thermostat and could cause personal injury

and/or property damage.

CAUTION

!

To prevent electrical shock and/or equipment

damage, disconnect electrical power to system

at main fuse or circuit breaker box until

installation is complete.

Leveling Thermostat

Leveling is for appearance only and

will not aect thermostat operation.

Specyfikacje produktu