Instrukcja obs艂ugi ESQ Analog Chronograph with Alarm
Przeczytaj poni偶ej 馃摉 instrukcj臋 obs艂ugi w j臋zyku polskim dla ESQ Analog Chronograph with Alarm (1 stron) w kategorii Ogl膮da膰. Ta instrukcja by艂a pomocna dla 12 os贸b i zosta艂a oceniona przez 6.5 u偶ytkownik贸w na 艣rednio 4.5 gwiazdek
Strona 1/1
Operating Instructions
Analog Chronograph with Alarm
1 2 3
H
E
C
D L
B
A
M
S
G
To activate/deactivate alarm:
Use push-button Cto toggle alarm on and off:
Two audible beeps indicate Alarm function is turned on; one beep
signals Alarm is turned off.
When Alarm sounds at set time, press button Cto stop beeping.
Chronograph Function Overview
Use push-buttons Aand Bto operate the chronograph.
NOTE: After 5-1/2 hours of continuous running, chronograph will
stop and reset automatically to conserve battery.
IMPORTANT: Crown must be in position 1 and hands must be at
zero before chronograph is started. If necessary, press button B
to reset hands to zero before beginning timing.
IMPORTANT: Do not push button Aor Bwhile crown is pulled to
position 2 or 3. If button Aor Bis accidentally activated while crown
is not flush against case, one or more of the chronograph hands will
become desynchronized. Should this occur, see directions below for
synchronizing hands.
Simple chronograph functions:
To measure the duration of a single, non-stop event:
1. Press button Ato start chronograph.
2. Press button Aa second time to stop chronograph, read
chronograph hands Eand Gto determine elapsed time.
3. Press button Bto reset chronograph to zero.
Split-time or intermediate time functions:
To take intermediate time readings as a race progresses:
1. Press button Ato start chronograph.
2. Press button Bto momentarily stop chronograph.
3. Read off the intermediate time.
4. Press button Bto resume chronograph function.
Hands will catch up with ongoing event.
5. To read a second split time, press button Bagain.
Repeat steps 2 through 4 to take any additional split times.
6. Press button Ato stop chronograph.
7. Take a reading of the final time.
8. Press button Bto reset chronograph hands to zero.
Synchronizing hands on Analog Chronograph with Alarm:
After changing the battery, or in the event of an error, the
chronograph hands can be realigned to zero if needed.
With crown in position 1, flush against case:
1. Press and hold buttons Aand Bsimultaneously for approximately
2 seconds to enter corrective mode.
2. Use button Bto realign chronograph minute counter hand E.
3. Use button Ato realign chronograph seconds hand G.
4. Press and hold buttons Aand Bsimultaneously to exit corrective
mode, with 2 chronograph hands now properly synchronized
at 12 o鈥檆lock/zero position.
Legend:
L - Alarm hand (12-hour)
H - Hour hand
M - Minute hand
S - Small seconds hand
E - Chronograph 30-minute counter
G - Chronograph seconds hand
D - Date window
1, 2, 3 - Crown positions
A - Chronograph push-button (start/stop)
B - Chronograph push-button (split/reset)
C - Alarm on/off push-button
A chronograph combines two time-keeping functions. It incorporates
a device to measure intervals of time independent of the regular time
shown on the dial. Your ESQ SWISS Analog Chronograph with Alarm
features a 30-minute counter, 12-hour alarm, and date display. It can
be used to time events up to 5 hours and 30 minutes in duration to
the nearest second.
To set the time:
1. Pull crown out to position 3.
2. Rotate crown in either direction to move hour Hand minute
Mhands to correct time.
3. Push crown back in to position 1.
To set the date:
CAUTION: Never set the date between 9:00 PM and 12:30 AM
when automatic calendar changes are taking place. Doing so could
damage the mechanism.
1. Pull crown out to position 2.
2. Rotate crown clockwise until correct date appears in window D.
3. Push crown back in to position 1.
To set alarm:
1. Pull crown out to position 2.
2. Turn crown counterclockwise until alarm hand Lis pointing to
desired time on bezel.
3. Push crown back in to position 1.
Specyfikacje produktu
| Marka: | ESQ |
| Kategoria: | Ogl膮da膰 |
| Model: | Analog Chronograph with Alarm |
Potrzebujesz pomocy?
Je艣li potrzebujesz pomocy z ESQ Analog Chronograph with Alarm, zadaj pytanie poni偶ej, a inni u偶ytkownicy Ci odpowiedz膮
Instrukcje Ogl膮da膰 ESQ
17 Wrze艣nia 2024
13 Wrze艣nia 2024
11 Wrze艣nia 2024
11 Wrze艣nia 2024
10 Wrze艣nia 2024
10 Wrze艣nia 2024
Instrukcje Ogl膮da膰
- Ogl膮da膰 Krontaler
- Ogl膮da膰 Orient
- Ogl膮da膰 Ticwatch
- Ogl膮da膰 Guess
- Ogl膮da膰 Stuhrling
- Ogl膮da膰 Westfalia
- Ogl膮da膰 WoodWatch
- Ogl膮da膰 Geemarc
- Ogl膮da膰 Speedo
- Ogl膮da膰 Christiaan Van Der Klaauw
- Ogl膮da膰 Lorus
- Ogl膮da膰 Alpina
- Ogl膮da膰 Omega
- Ogl膮da膰 IWC
- Ogl膮da膰 Obaku
Najnowsze instrukcje dla Ogl膮da膰
30 Marca 2025
26 Marca 2025
26 Marca 2025
13 Marca 2025
13 Marca 2025
13 Marca 2025
13 Marca 2025
