Instrukcja obsługi Evga XC3
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Evga XC3 (2 stron) w kategorii Nie skategoryzowane. Ta instrukcja była pomocna dla 32 osób i została oceniona przez 16.5 użytkowników na średnio 4.7 gwiazdek
Strona 1/2
Installation Guide
All steps include removing the original shroud, heatsink, and screws, and then replacing those with the included new shroud, heatsink, waterblock, and provided
screws, with a few exceptions. The number of provided screws used will vary depending on whether the card uses a backplate. Several included accessories may
include extras. EVGA recommends a Phillips #1 screwdriver for all screws.
All suitable P/N for HYBRID installation are listed below. Please refer to the following table.
The following instructions and pictures are provided to assist your installation of the EVGA XC3 Hybrid Cooling Kit to the EVGA GeForce RTX™ 3090 and 3080
graphics cards. Please be careful installing the Kit; there are several very small fasteners used that can be stripped if you are not careful.
Please be sure to keep your original shroud, heatsink, and screws so your card can be returned to its original condition in
case you ever need to submit for warranty.
Included Accessories:
3. Remove the 3 screws on the I/O bracket and set them aside. You will reuse
them later.
Instructions:
1. Remove the 8 BP screws circled in red and carefully remove the backplate (if
present). Next, remove the 4 GPU screws circled in blue and remove the GPU
bracket.
For RTX 3090 XC3 ULTRA and XC3 cards: Removing the backplate may require
some force to loosen up the thermal pads. Make sure to place the thermal pads
on the backplate as shown in the image below, as you will reuse the backplate
and thermal pads.
2. Turn the card over and remove the heatsink from the card. Remove the fan
connectors (blue, beige, and black) first, and then the LED connector (black) as
you lift the heatsink o the card.
RTX™ 3090 XC3 ULTRA
RTX™ 3090 XC3
RTX™ 3090 XC3 BLACK
RTX™ 3080 XC3 ULTRA
RTX™ 3080 XC3
RTX™ 3090 XC3 BLACK
24G-P5-3975-KR
24G-P5-3973-KR
24G-P5-3971-KR
10G-P5-3885-KR
10G-P5-3883-KR
10G-P5-3881-KR
11
12
9
10
8
7
1 32
5
4
6
13
EVGA HYBRID Shroud with VRM Heatsinks/Fan Bracket
GPU & Memory Baseplate
EVGA HYBRID Pump and Radiator
M2.5 x 6.9mm spring screws (GPU). 7 pcs. PN: BAA125069001
M2 x 8.5mm Backplate screws (BP). 10 pcs. PN: BAA120085039
Mylar washers for spring screws. 5 pcs. PN: BGD100000003
1
2
3
4
5
6
Rubber plugs. 3 pcs. PN: BGB030007002
Tube Bracket. 1 pc. PN: BJD243038000
M2 x 7mm tube bracket screws. 2 pcs. PN: BAA120070024
Zip ties 4pcs and EVGA Cable ties 2pcs
8pcs screws and 8pcs washers to mount radiator
8
9
10
11
12
Thermal Grease 1 pack
13
M2 x 5mm screws (PCB). 15pcs. PN: BAA120050054
7
4. Using a lint-free cloth and high-percentage isopropyl alcohol, carefully clean
the GPU and remove any leftover thermal putty on the graphics card in the
regions marked below. Try to replace any loose thermal pads back onto the
original heatsink/cooler in case you need to restore the card to its original
condition.
Specyfikacje produktu
| Marka: | Evga |
| Kategoria: | Nie skategoryzowane |
| Model: | XC3 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Evga XC3, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Nie skategoryzowane Evga
30 Marca 2025
Instrukcje Nie skategoryzowane
- Whirlpool
- Neewer
- Navman
- Hansa
- Advantech
- Magewell
- Hager
- Havis
- Phoenix Contact
- Crosley
- Brizo
- Newline
- Silverline
- Sunding
- Lahti Pro
Najnowsze instrukcje dla Nie skategoryzowane
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025