Instrukcja obsługi Extron FOX 3G HD-SDI P SM
Extron
Wzmacniacz sygnału WiFi
FOX 3G HD-SDI P SM
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Extron FOX 3G HD-SDI P SM (2 stron) w kategorii Wzmacniacz sygnału WiFi. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 6 użytkowników na średnio 4.5 gwiazdek
Strona 1/2
This guide provides instructions for an experienced installer to set up and operate
Extron
®
FOX 3G HD-SDI Transceiver.
The transceiver can be configured via its rear panel Mode DIP switches to operate in one
of three ways:
• Bidirectional transceiver
• Transmitter
• Receiver
See Transceiver Configurations on the rear of this guide if you need more information.
NOTE: In this guide, the term “transceiver” refers to any FOX 3G HD-SDI; the term “bidirectional transceiver” refers to a
FOX 3G HD-SDI specifically configured as a bidirectional transceiver.
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources and mount the transceiver as required.
Step 2 — Connections and Initial Settings
a
HD-SDI Input connector — If the FOX 3G HD-SDI is configured as
either a bidirectional transceiver or as a transmitter, connect an
HD-SDI, SDI, or 3G-SDI video input to this BNC connector.
b
Mode switches — Set these DIP switches to the
positions shown at right to select the transceiver
configuration. See Transceiver Configurations on the
rear of this guide for more information.
c
Fiber optic connectors —
WARNING: This unit outputs continuous invisible light, which may be harmful to the eyes; use with caution. For
additional safety, plug the attached dust caps into the optical transceivers when the fiber optic cable is
unplugged.
NOTE: Ensure that you use the proper fiber cable for your transceivers. Typically, singlemode fiber cable has a
yellow jacket and multimode fiber cable has an orange or aqua jacket.
Tx connector — In any configuration, connect a fiber optic cable to the Optical Tx LC connector.
Connect the free end of this fiber optic cable to the Optical Rx connector on another FOX 3G HD-SDI transceiver that is
configured as a bidirectional transceiver or as a receiver.
Rx connector — In either the bidirectional transceiver or receiver configuration, connect a fiber optic cable to the
Optical Rx connector to receive the signal from the transmitting unit. Connect the free end as detailed below:
• In a 2-transceiver system, connect the free end of this cable to the Optical Tx connector on the transmitting unit,
which is configured as a transmitter.
• In a daisy-chained system, connect the free end of this cable to the Optical Tx connector on the previous unit in the
daisy chain (configured as either a bidirectional transceiver or a transmitter).
d
Buffered Outputs connectors — In any FOX 3G HD-SDI configuration , connect a digital display to these BNC connectors.
In the bidirectional transceiver configuration, connectors 1 and 2 both output the video that is sent from the other
transceiver.
In the receiver configuration, only connector 2 outputs video and it is the
video sent by the transmitting unit.
In the transmitter configuration, connectors 1 and 2 both output the video
signal that is input on the HD/SDI Input connector,
a
, on the same transceiver.
e
Plug the included external 12 VDC power supply into this Power connector —
2-pole captive screw connector as shown at right. Use the supplied tie-wrap to
strap the power cord to the extended tail of the connector.
12V
0.3A MAX
FOX HDSDI
HD/SDI IN
POWER
BUFFERED OUTPUTS
MODE
OPTICAL
RxTx
1 2
1 2
25 1
3 4
SW2 Mode
Down
Down
Up
Up
Down
Up
Down
Up
Bidirectional transceiver ( )default position
Transmitter with local monitor outputs
Receiver with daisy chaining
Spare (functions as receiver with daisy chaining)
SW1
MODE
1 2
Power Supply
Output Cord
SECTION
A–A
Ridges
Smooth
A A
Tie Wrap
3
5
1
FOX 3G HD-SDI Setup Guide
Specyfikacje produktu
| Marka: | Extron |
| Kategoria: | Wzmacniacz sygnału WiFi |
| Model: | FOX 3G HD-SDI P SM |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Extron FOX 3G HD-SDI P SM, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Wzmacniacz sygnału WiFi Extron
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
Instrukcje Wzmacniacz sygnału WiFi
- Asus
- Iogear
- 7inova
- Tenda
- HELGI
- Gefen
- Elektrobock
- Silex
- Axis
- Conrad
- Totolink
- TRENDnet
- NetComm
- Digi
- Vision
Najnowsze instrukcje dla Wzmacniacz sygnału WiFi
29 Marca 2025
29 Marca 2025
24 Marca 2025
21 Lutego 2025
20 Lutego 2025
20 Lutego 2025
20 Lutego 2025
20 Lutego 2025
5 Lutego 2025
5 Lutego 2025