Instrukcja obsługi Fantini Cosmi ECCM32
Fantini Cosmi
Sprzęt pomiarowy
ECCM32
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Fantini Cosmi ECCM32 (12 stron) w kategorii Sprzęt pomiarowy. Ta instrukcja była pomocna dla 13 osób i została oceniona przez 7 użytkowników na średnio 4.4 gwiazdek
Strona 1/12
ECCM32 Installation manual
(cod. 5679612 Rev.1)
Page 1 of 12
ECCM32
Energy calculator
for heat metering
INSTALLATION MANUAL
This manual is intended for qualified, previously trained
personnel: therefore, it does not provide basic information
concerning the general application context.
The “Advanced programming and user’s guide ECCM ” and the “
Service” configuration software can be downloaded from
“www.fantinicosmi.it” web site.
Warning! This unit contains “lithium-thionyl chloride”
batteries that may be potentially dangerous.
Read through the safety precautions for use in chapter 14.
1. Introduction
The ECCM32 unit is an electronic device used for heat sub metering
in heating and cooling systems as well as the volumes of cold and
hot sanitary water meters.
The calculator features separate sections able to simultaneously
record the following:
•
thermal energy in a heating and cooling circuit;
•
sanitary cold water volume;
•
sanitary hot water volume.
The unit has been designed to facilitate the installation and reduce
the time needed for the commissioning operations.
The ECCM32 unit is equipped with a wired “M-Bus” interface and a
wired “Local-bus” interface that allow the user to read, by means
of compatible equipment, the consumption from inside one’s own
apartment.
2. Package contents
• Calculator;
• Installation kit including:
one supporting bracket- two screws 3x6mm – one screw
2,9x9,5mm – one O-ring – two security seals;
• Installation manual.
3. General information
• Read through and strictly comply with the instructions and
specifications contained in this manual.
• The unit shall be installed, maintained and repaired by qualified
personnel, in accordance with the general prescriptions
concerning the electric equipment installation.
• This type of product is ruled by the EN1434 Standard (parts 1÷6)
and the 2004/22/CE Directive (Annex MI-004). Moreover, the
national standards concerning the calibration, verification and
validity, as applicable in the country where the equipment is
operated, shall be complied with.
• The certified manufacturing process guarantees the correct
operation of the unit and the conformity to the safety standards.
The warranty will be null and void if the seals inside the unit are
damaged or have been removed, or if any arbitrary modification
is made to the unit itself.
• The unit shall be cleaned, if necessary, by using only a cloth
moistened with water.
• The flow meter and the electronic unit shall have the same
impulse rate.
• The cables shall be kept at least 20 cm far from electromagnetic
interference sources (e.g. switches, regulators, circulation pumps,
etc.) and, also, at least 5 cm far from other electric cables.
4. Installation
4.1. Installing the calculator
The calculator is factory-set to the “delivery” mode, as
evidenced by the OFF writing on the display.
The keys shall be pressed only to proceed with “commissioning”
(refer to chapter 11) upon completion of the installation and
connection operations.
Open the calculator by acting on the two side hooks to remove the
upper assembly with the electronic section.
Carefully put the electronic section aside in the package.
Remove the fastening bracket from the bottom section and fix it to
the wall; then, fit the bottom onto the bracket and fix it by making
use of the “anti-removal” kit (i.e. screw and O-ring) supplied
together with the unit.
The special seals shall be put onto the calculator following the
installation and commissioning operations.
MID examination certifica
CH-MI004-13017
Specyfikacje produktu
| Marka: | Fantini Cosmi |
| Kategoria: | Sprzęt pomiarowy |
| Model: | ECCM32 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Fantini Cosmi ECCM32, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Sprzęt pomiarowy Fantini Cosmi
8 Września 2024
2 Września 2024
26 Sierpnia 2024
22 Sierpnia 2024
22 Sierpnia 2024
Instrukcje Sprzęt pomiarowy
- LaCie
- Chauvin Arnoux
- Beurer
- NEO Tools
- Microlife
- Ridgid
- Atmel
- CSL
- Hazet
- Oscium
- Hikmicro
- Intact
- Apollo Ultrasonic
- Multimetrix
- Mitutoyo
Najnowsze instrukcje dla Sprzęt pomiarowy
3 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025