Instrukcja obsługi Futaba P-FTM-TFH
Futaba
Zabawki sterowane radiem
P-FTM-TFH
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Futaba P-FTM-TFH (8 stron) w kategorii Zabawki sterowane radiem. Ta instrukcja była pomocna dla 21 osób i została oceniona przez 11 użytkowników na średnio 4.1 gwiazdek
Strona 1/8
powered by
INSTRUCTION MANUAL
Item-No. P-FTM-TFH
TM-24
FUTABA 2.4 GHz T-FHSS Module F-Series
2 Instruction Manual TM-24 Module
This transmitter module is developed to convert
existing Futaba transmitters to the 2.4 GHz
frequency band with previous 35/40 MHz trans-
mission frequencies. The following instruction
manual explains in detail the connection and
operation of the TM-24 Module with the Futaba
F-14 transmitter as an example. The connecti-
on can be done with almost all transmitters via
existing plug connections, but some transmitters
require simple soldering. The installation can also
be done by our Futaba service against payment.
Installation Of 2.4 GHz Antenna
Two of the switch holes on the front side of the
transmitter are required to mount the transmitter
antenna. The clear cover plate can remain, only
the holes have to be opened.
If the existing holes are already fully occupied
with switch / prop modules, the transmitter anten-
na socket can also be attached to the left or right
front of the transmitter. For this, two holes with
D = 6mm must be drilled. The illustrated drilling
template can be used for this purpose. (See
pictures, also for the status LED).
Drilling template for antenna mounting on the
front side of the transmitter
Connecting The Module To The Transmitter
For connection, the enclosed adapter cable with
PCB is used.
The 3-pin connector (servo plug) of the adapter
cable F-14 with additional board is connected
to the corresponding plug-in contact (module
connection) of the TM-24 module. Observe
polarity! The black connecting wire of the plug
cable must point inwards towards the module
board (minus). It is important to ensure that all
3 contacts are plugged in at all times. The white
connection wire must point to the outer edge of
the module (signal line).
FürdieBefestigungderSendeantenne
werdenzweiderSchalterlöcherander
15mm
Antennenkabel
rdieBefestigungderSendeantenne
rdenzweiderSchalterlöcherander
SAFETY INSTRUCTIONS
Please read carefully the safety
instructions within the manual of
your transmitter!
TM-24 T-FHSS Module
Antenna Wire
powered by
3www.ripmax.com
Connection To Transmitter
The signal connector for the TM-24 module is
connected to the Trainer socket (4-pin) of the
transmitter F-14 using the adapter cable-trainer
connector. The plug-in contact is reverse-polarity
protected, but do not forcefully press it. One pin
of the plug is not used.
LED Connector
The connector of the LED is connected to the
LED connector. It is not possible to reverse the
polarity, but it should be done with a little „sensiti-
auchfürdieStatusLED,s.u.).
BohrschablonefürAntennen- MontageseitlichvorneamSender
15mm
Antennenkabel
-
+
S
LED-Anschluss
Modulanschluss
Binding-Taster
Antennenclip
AUS EIN
Modul-Schalter
Akkustecker
+
-
Akku Buchse F-14
Trainer-Buchse F-14
Adpater-Platine
Adapter PCB
vity“ in order not to damage the plug.
The LED with bracket is installed either in an
existing hole on the switch mounting brackets or
as shown in the gure.
Antenna Clip
The antenna cable has a connection clip, the
counterpart is seated on the module board (see
photo). The clip must be positioned carefully and
centrally to the round edge of the clip onto the
counterpart (antenna socket) and then depres-
sed carefully until a noticeable snapping action
occurs.
ATTENTION! This is an important task for the
safe operation of the F-14, which can have a
signicant impact on the achievable range and
transmission safety, so perform this procedure
accurately and correctly.
Connecting To TX Battery
The adapter board allows Futaba TX batteries to
be connected to the „old“ plug system and the
PCB Connection
Trainer Socket F-14
Battery Socket F-14
Module
Connector Link Button
Antenna Clip
LED Connector
Battery Plug
Module Switch
ON OFF
Specyfikacje produktu
| Marka: | Futaba |
| Kategoria: | Zabawki sterowane radiem |
| Model: | P-FTM-TFH |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Futaba P-FTM-TFH, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Zabawki sterowane radiem Futaba
5 Lutego 2025
5 Lutego 2025
5 Lutego 2025
15 Stycznia 2025
4 Października 2024
27 Września 2024
16 Września 2024
14 Września 2024
14 Września 2024
11 Września 2024
Instrukcje Zabawki sterowane radiem
- Zabawki sterowane radiem Spin Master
- Zabawki sterowane radiem Flyzone
- Zabawki sterowane radiem Ripmax
- Zabawki sterowane radiem Tamiya
- Zabawki sterowane radiem Velleman
- Zabawki sterowane radiem HPI Racing
- Zabawki sterowane radiem ARRMA
- Zabawki sterowane radiem Parrot
- Zabawki sterowane radiem Sharper Image
- Zabawki sterowane radiem SkyRC
- Zabawki sterowane radiem ACME
- Zabawki sterowane radiem LRP
- Zabawki sterowane radiem Carrera
- Zabawki sterowane radiem FMS
- Zabawki sterowane radiem ROCHOBBY
Najnowsze instrukcje dla Zabawki sterowane radiem
31 Marca 2025
30 Marca 2025
30 Marca 2025
30 Marca 2025
30 Marca 2025
30 Marca 2025
29 Marca 2025
29 Marca 2025
29 Marca 2025
29 Marca 2025