Instrukcja obsługi Garmin GPS 24xd NMEA 2000
Garmin
Niesklasyfikowane
GPS 24xd NMEA 2000
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Garmin GPS 24xd NMEA 2000 (36 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 5 użytkowników na średnio 4.7 gwiazdek
Strona 1/36
GPS 24XD NMEA 2000®
INSTALLATION INSTRUCTIONS
Important Safety Information
Important Safety Information
Important Safety Information
Important Safety InformationImportant Safety Information
CAUTION
To avoid possible personal injury, always wear safety goggles, ear protection, and a dust mask when drilling,
cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite side of the surface to avoid damaging the vessel.
For the best performance and to avoid damage to your boat, read all installation instructions before
proceeding. Install the device per these instructions. Use the appropriate fasteners, tools, and mounts listed,
which are available at most marine dealers.
The Garmin® GPS 24xd NMEA 2000 high-sensitivity GPS antenna provides position information to your existing
NMEA 2000 network. If your boat does not have a NMEA 2000 network, you will need to install one.
For more information, go to .garmin.com
Tools Needed
Tools Needed
Tools Needed
Tools NeededTools Needed
• Drill
• 3.2 mm (1/8 in.) drill bit
• 19 mm (3/4 in.) drill bit for a pole-mount cable-hole
• 25 mm (1 in.) hole saw for a surface-mount cable-hole
• Countersink bit for mounting on fiberglass
• Screws for under-deck mounting
• Screwdriver, appropriate for the screw type
• Marine sealant (optional)
• Additional NMEA 2000 network components as needed
TA-2020/6796
GUID-28CE8C25-CFD8-4C12-B6D0-AD9CDF4D5084 v3June 2021
Mounting the Antenna
Mounting the Antenna
Mounting the Antenna
Mounting the AntennaMounting the Antenna
Antenna Mounting Considerations
Antenna Mounting Considerations
Antenna Mounting Considerations
Antenna Mounting ConsiderationsAntenna Mounting Considerations
CAUTION
Do not install or store the antenna near strong magnets, including speakers. A strong magnetic field can
damage the antenna.
You can mount the antenna on a flat surface or attach it to a standard 1 in. OD, 14 threads per inch, pipe-
threaded pole (not included). You can route the cable outside of the pole or through the pole. For best
performance, consider these guidelines when selecting the antenna mounting location.
• To ensure the best reception, the antenna should be mounted in a location that has a clear, unobstructed
view of the sky in all directions .
• The antenna should not be mounted where it is shaded by the superstructure of the boat , a radome
antenna, or the mast.
• The antenna should not be mounted near the engine or other sources of Electromagnetic Interference (EMI)
.
• The antenna should not be mounted near known ferrous metal objects such as a toolbox or compass.
• A handheld compass should be used to test for magnetic interference in the area where the antenna is to be
mounted. Your boat, motors, and devices must be on during the test.
If the needle on the handheld compass moves when you hold it where you intend to mount the antenna,
magnetic interference is present. You must choose another location and test again.
• Mounting screws are provided with the antenna. If you use mounting hardware other than the provided
screws, the hardware must be made of quality stainless steel or brass material to avoid magnetic
interference with the antenna.
NOTE: Test all mounting hardware with a handheld compass to make sure no magnetic fields are present in
the hardware.
• If a radar is present, the antenna should be mounted above the path of the radar . If necessary, the
antenna may be mounted below the path of the radar .
• The antenna should not be mounted directly in the path of the radar .
• The antenna should not be mounted within 1 m (3 ft.) of a VHF radio antenna or the path of a radar .
2
Testing the Mounting Location
Testing the Mounting Location
Testing the Mounting Location
Testing the Mounting LocationTesting the Mounting Location
1Temporarily secure the antenna in the preferred mounting location and test it for correct operation.
2If you experience interference with other electronics, move the antenna to a different location, and test it
again.
3Repeat steps 1–2 until you observe full or acceptable signal strength.
4Permanently mount the antenna.
3
Specyfikacje produktu
| Marka: | Garmin |
| Kategoria: | Niesklasyfikowane |
| Model: | GPS 24xd NMEA 2000 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Garmin GPS 24xd NMEA 2000, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Garmin
10 Stycznia 2025
10 Stycznia 2025
31 Grudnia 2025
14 Października 2024
9 Października 2024
7 Października 2024
4 Października 2024
4 Października 2024
3 Października 2024
2 Października 2024
Instrukcje Niesklasyfikowane
- Niesklasyfikowane Nubert
- Niesklasyfikowane Strex
- Niesklasyfikowane Switel
- Niesklasyfikowane MOZA
- Niesklasyfikowane EPH Elektronik
- Niesklasyfikowane Shure
- Niesklasyfikowane Petmate
- Niesklasyfikowane Heller
- Niesklasyfikowane BDI
- Niesklasyfikowane Flycam
- Niesklasyfikowane Gima
- Niesklasyfikowane MedFolio
- Niesklasyfikowane Duracell
- Niesklasyfikowane Esperanza
- Niesklasyfikowane Audioline
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025