Instrukcja obsługi Garmin GPSMAP 10x2
Garmin
Niesklasyfikowane
GPSMAP 10x2
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Garmin GPSMAP 10x2 (6 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 4 użytkowników na średnio 4.6 gwiazdek
Strona 1/6
GPSMAP® 10X2/12X2 SERIES
INSTALLATION
INSTRUCTIONS
Important Safety Information
WARNING
Failure to follow these warnings, cautions, and notices could
result in personal injury, damage to the vessel or device, or poor
product performance.
See the guide in the Important Safety and Product Information
product box for product warnings and other important
information.
When connecting the power cable, do not remove the in-line
fuse holder. To prevent the possibility of injury or product
damage caused by fire or overheating, the appropriate fuse
must be in place as indicated in the product specifications. In
addition, connecting the power cable without the appropriate
fuse in place voids the product warranty.
CAUTION
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
To avoid possible personal injury or damage to the device and
vessel, disconnect the vessel's power supply before beginning
to install the device.
To avoid possible personal injury or damage to the device or
vessel, before applying power to the device, make sure that it
has been properly grounded, following the instructions in the
guide.
NOTICE
For the best possible performance, the device must be installed
according to these instructions.
When drilling or cutting, always check what is on the opposite
side of the surface to avoid damaging the vessel.
Read all installation instructions before proceeding with the
installation. If you experience difficulty during the installation,
contact Garmin® Product Support.
Contacting Garmin Support
• Go to for help and information, such as support.garmin.com
product manuals, frequently asked questions, videos, and
customer support.
• In the USA, call 913-397-8200 or 1-800-800-1020.
• In the UK, call 0808 238 0000.
• In Europe, call +44 (0) 870 850 1241.
Software Update
You may need to update the chartplotter software after
installation. For the instructions on how to update the software,
see the owner's manual at www.garmin.com/manuals
/GPSMAP10x2-12x2.
Tools Needed
• Drill
◦ Bail mount: drill bits appropriate for the surface and
hardware
◦ Flush mount: 14 mm (9/16 in.), 6 mm (1/4 in.) and 3.6 mm
(9/64 in.) (with nut plate), or 3.2 mm (1/8 in.) drill bit (with no
nut plate)
• #2 Phillips screwdriver
• Jigsaw or rotary tool
• File and sandpaper
• Marine sealant (recommended)
Mounting Considerations
NOTICE
This device should be mounted in a location that is not exposed
to extreme temperatures or conditions. The temperature range
for this device is listed in the product specifications. Extended
exposure to temperatures exceeding the specified temperature
range, in storage or operating conditions, may cause device
failure. Extreme-temperature-induced damage and related
consequences are not covered by the warranty.
When selecting a mounting location, you should observe these
considerations.
• The location should provide optimal viewing as you operate
your boat.
• The location should allow for easy access to all device
interfaces, such as the keypad, touchscreen, and card
reader, if applicable.
• The location must be strong enough to support the weight of
the device and protect it from excessive vibration or shock.
• To avoid interference with a magnetic compass, the device
should not be installed closer to a compass than the
compass-safe distance value listed in the product
specifications.
• The location must allow room for the routing and connection
of all cables.
• The location must not be a flat, horizontal surface. The
location should be in a vertical angle.
The location and viewing angle should be tested before you
install the device. High viewing angles from above and below
the display may result in a poor image.
Bail Mounting the Device
NOTICE
If you are mounting the bracket on fiberglass with screws, it is
recommended to use a countersink bit to drill a clearance
counterbore through only the top gel-coat layer. This will help to
avoid cracking in the gel-coat layer when the screws are
tightened.
You can use a bail mount bracket (not included) to bail mount
the device on a flat surface.
1Using the bail-mount bracket as a template, mark the pilot
holes.
GUID-BF1B0D74-52BF-4F5B-938B-9A7556F36E8C v3October 2020
Specyfikacje produktu
| Marka: | Garmin |
| Kategoria: | Niesklasyfikowane |
| Model: | GPSMAP 10x2 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Garmin GPSMAP 10x2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Garmin
10 Stycznia 2025
10 Stycznia 2025
31 Grudnia 2025
14 Października 2024
9 Października 2024
7 Października 2024
4 Października 2024
4 Października 2024
3 Października 2024
2 Października 2024
Instrukcje Niesklasyfikowane
- KMA Machines
- Smoby
- BikeLogger
- Modbap Modular
- REL Acoustics
- Moen
- BabyHome
- Traxxas
- K&M
- Powerblade
- McCulloch
- Victron Energy
- My Arcade
- Sony Optiarc
- Gram
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025