Instrukcja obsługi Garmin LIDAR-Lite v4 LED
Garmin
nieskategoryzowany
LIDAR-Lite v4 LED
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Garmin LIDAR-Lite v4 LED (10 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 70 osób i została oceniona przez 35.5 użytkowników na średnio 4.3 gwiazdek
Strona 1/10
LIDAR-LITE V4 LED
OPERATION MANUAL AND
TECHNICAL SPECIFICATIONS
Specifications
Specification Measurement
Unit dimensions (L × W × H)
NOTE: Measurements do not
include an attached connector.
52.2 x 24 x 21.2 mm (2.1 x 0.9 x
0.8 in.)
Weight 14.6 g (0.5 oz.)
Operating temperature -20 to 60°C (-4 to 140°F)
Storage temperature -40 to 85°C (-40 to 185°F)
Power (operating voltage) 4.75 to 5.25 Vdc
Current consumption 2 mA idle
85 mA during an acquisition
Input voltage (VIN) 3.3 V Max
Range 5 cm (1.97 in.) to 10 m (32.8 ft.)
Resolution 1 cm (0.4 in.)
Beam divergence 4.77 degrees
LED wavelength 940 nm
Optical aperture 14.9 mm
Update rate I2C: Greater than 200 Hz typical
ANT: Up to 200 Hz to a 90%
reflective target indoors at 2 m in
normal operating mode
Interface I2C or ANT®
Configurable for SPI with user
applications
Measurement repeatability
NOTE: As measured indoors to a
90% reflective target; 1 cm is
equivalent to 1 standard deviation.
Measurements were obtained
using high accuracy mode.
± 1 cm to 2 m
± 2 cm to 4 m
± 5 cm to 10 m
Device Dimensions
52.17 mm (2.05 in.)
44.98 mm (1.77 in.)
10.6 mm (0.42 in.)
24.03 mm (0.95 in.)
1 mm (0.04 in.)
18 mm (0.71 in.)
21.35 mm (0.84 in.)
21.2 mm (0.83 in.)
Mounting Options
Cable tie: You can secure the device to your application using a
3.6 mm (0.14 in.) wide cable tie. You should route the cable
tie through the channel in the center of the device.
Double-sided tape: You can secure the bottom of the device to
your application using double-sided tape. For best results,
you should select a tape that has a high-strength bond.
Labeling Requirements
The LIDAR-Lite v4 LED device is an FCC-certified transmitter. If
you are integrating the device with another product, you must
ensure the FCC ID is visible from the outside of your product.
You are responsible for meeting any other labeling requirements
imposed by the FCC rules and any rules related to the
compliance of your end product.
Connections
LIDAR-Lite v4 LED Connection Diagram
The through-holes on the LIDAR-Lite v4 LED device are
arranged in 2 rows of 5 holes each, with a 2 mm pitch between
each connection.
NOTICE
The LIDAR-Lite v4 LED maximum signal level is 3.3 V. A signal
greater than 3.3 V will damage the device.
Pin Pin Name Function V Max
VIN 5 V Power 5 V
GND Ground --
I2C SDA I2C Data 3.3 V
GUID-48127269-EFD8-41FF-93EC-D21B0A1EFE74 v2September 2020
Specyfikacje produktu
| Marka: | Garmin |
| Kategoria: | nieskategoryzowany |
| Model: | LIDAR-Lite v4 LED |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Garmin LIDAR-Lite v4 LED, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje nieskategoryzowany Garmin
28 Lipca 2024
27 Maja 2024
27 Maja 2024
27 Maja 2024
27 Maja 2024
24 Maja 2024
24 Maja 2024
24 Maja 2024
23 Maja 2024
23 Maja 2024
Instrukcje nieskategoryzowany
- Vertex
- Plant Craft
- Helios
- Consul
- Blizzard
- Arthur Martin
- Bertazzoni
- DeWalt
- APC
- Horizon Fitness
- Maginon
- Taylor
- Ciclo
- Dehner
- Morley
Najnowsze instrukcje dla nieskategoryzowany
28 Października 2024
28 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024