Instrukcja obsługi Hager EE805A
Hager
detektor ruchu
EE805A
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hager EE805A (2 stron) w kategorii detektor ruchu. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 6.5 użytkowników na średnio 5.0 gwiazdek
Strona 1/2
1 09/2017 - 6LE002943AHager Controls S.A.S., 33 rue Saint-Nicolas, B.P. 10140, 67703 SAVERNE CEDEX, France - www.hager.com
6LE002943A
EE804A
Presence and motion detector
360°, surface-mounted
EE805A
Presence and motion detector
360°, flush-mounted
z
Design and layout of the device
(Figure 1/2)
(1) Connecting terminals
(2) Mounting device locking screw
(3) Release opening
(4) Fastening grids
(5) Detector lens
(6) Response brightness potentiometer
(7) Potentiometer delay time
(8) Cover for potentiometer
(9) Locking screw
(10) Fixing springs
(11) Strain relief with mounting device for cable
ties
(12) Cover for connection compartment
Function
Correct use
- automatic switching of electric loads depend-
ing on heat motion and ambient brightness
- EE804A: Surface-mounted installation or in-
stallation on mounting box according to DIN
49073
- EE805A: Cavity installation
Product characteristics
- Combination of presence and motion detector
with enhanced detection sensitivity in the cen-
tral presence-detection area
- Response brightness adjustable
- Delay time adjustable
Behaviour during operation
The motion detector detects heat motion caused
by people, animals, or objects.
- will be switched on for the delay time if move-
ments are detected in the detection area and
the set response brightness is undershot.
Each detected movement restarts the delay
time.
- will be switched off if no additional movements
are detected in the detection area and the set
delay time has elapsed or the set response
brightness is exceeded.
Information for electricians
Installation and electrical connection
DANGER!
Touching live parts can result in an
electric shock!
An electric shock can be lethal!
Disconnect the connecting cables
before working on the device and
cover all live parts in the area!
ç
Selecting installation location
The motion detector must be installed horizontally
on the ceiling. It has an detection angle of 360°.
The diameter of the detection area depends on the
installation height. At an installation height of 2.5
m, the diameter at ground level is approx. 6 m. The
diameter of the inner detection area with enhanced
detection sensitivity is 4 m (gure 3).
At an installation height greater than 2.5 m, the
detection area increases. At the same time, the
detection sensitivity decreases.
Observe the motion orientation: a distinction is
made between "direct approach" and "trans-
verse motion". Motions transverse to the motion
detector can be detected better than motions
toward the motion detector (Fig. 4).
If used as a presence detector, the device must
be installed so that areas with less motion activ-
ity (desk, seating area) are within the detection
area (gure 3).
Avoid sources of interference in the detection
area. Sources of interference, e.g. heating
elements, ventilation systems, air conditioners
and lamps that are cooling down can cause
undesired switching (Fig. 5).
Select an installation location that is free of
vibration. Vibrations can cause undesired
switching.
Connecting and installing the surface-mounted
variant EE804A (gure 7)
Run the connection cable through the insertion
opening (13).
Install device socket under the cover using the
screw dowel set enclosed. Installation can be
done on a ush-mounted box if available
Connect device according to connection dia-
gram (gure 6).
Snap onto base
Screw in locking screw (9).
Congure settings.
Close cover (8).
z
Safety instructions
Electrical equipment may only be installed and
assembled by a qualied electrician in accord-
ance with the relevant installation standards,
regulations, directives and safety and accident
prevention directives of the country.
Failure to comply with these installation in-
structions may result in damage to the device,
re or other hazards.
Due to its detection behaviour the device is not
suitable for use in burglary detection or alarm
systems.
These instructions are an integral component of
the product and must be retained by the end user.
(1)
(8)
(9)
(2)
(3)
(5)
(4)
(6) (7)
1
4
(4)
(5)
(10)
(11)
(12)
(10)
2
(6) (7)
0 m 2 m2 m
1 m
2 m
2,5 m
3 m3 m
3
Specyfikacje produktu
| Marka: | Hager |
| Kategoria: | detektor ruchu |
| Model: | EE805A |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Hager EE805A, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje detektor ruchu Hager
9 Grudnia 2024
9 Grudnia 2024
9 Grudnia 2024
16 Września 2024
5 Września 2024
5 Września 2024
14 Sierpnia 2024
14 Sierpnia 2024
14 Sierpnia 2024
14 Sierpnia 2024
Instrukcje detektor ruchu
- RAB
- Techly
- Vimar
- Smartwares
- Vernier
- Suevia
- Homematic IP
- Xavax
- Schwaiger
- XQ-lite
- EQ-3
- Pepperl+Fuchs
- Iget
- EQ3
- Extron
Najnowsze instrukcje dla detektor ruchu
9 Stycznia 2025
29 Grudnia 2024
29 Grudnia 2024
26 Grudnia 2024
26 Grudnia 2024
25 Grudnia 2024
17 Grudnia 2024
17 Grudnia 2024
17 Grudnia 2024
17 Grudnia 2024