Instrukcja obsługi Hager TYM632C

Hager nieskategoryzowany TYM632C

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hager TYM632C (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 6 użytkowników na średnio 4.9 gwiazdek

Pobierz PDF

Strona 1/2

6LE002527A

TYM632C

Output 12gang shutter/blind

230V~

TXM632C

Output 12gang shutter/blind

230V~

Bn?.:

6LE002527A1

Safety instructions

Electrical equipment may only be installed and

assembled by a qualied electrician in accord-

ance with the relevant installation standards,

guidelines, regulations, directives, safety and

accident prevention regulations of the country.

Failure to comply with these installation in-

structions may result in damage to the device,

re or other hazards.

Hazard due to electric shock. Disconnect be-

fore working on the device or load. Take into

account all circuit breakers that supply danger-

ous voltages to the device or load.

Connect one motor per output only. If several

motors are connected, motors or device might

be destroyed.

Use drives with mechanical or electrical nal

position switches only. Check nal position

switches for correct adjustment. Observe mo-

tor manufacturer's data. The device can be

damaged.

Do not connect any three-phase motors. The

device can be damaged.

Risk of injury. Use the device to control blind

and shutter drives or awnings only. Do not

switch any other loads.

Observe the motor manufacturer's data regard-

ing change-over time and max. switch-on time

(ED).

These instructions are an integral component

of the product and must be retained by the end

user.

Design and layout of the device

C1/C7 C3/C9 C5 /C11

C2/C8 C4/C10 C6/C1 2

3 4 5 6 7 8 9 101 2

N L

L L

230V 50/60 Hz

L L CC6C4C2

18 19 20 2 1 22 23 2 4 25 26

auto 1

auto 2

(1)

(2) (3)

(4) (5)

(6)

(3)

(7)

Figure 1: Device overview

(1) Slide switch / 1/ 2auto1/auto2

(2) KNX bus connection terminal

(3) Connections of loads

(4) Labelling eld with cover

(5) Illuminated programming button

(6) Operation button for manual operation per

output with status LED

(7) Mains power supply connection

Function

System information

This device is a product of the KNX system and

corresponds to the KNX guidelines. Detailed

specialised knowledge obtained from KNX training

courses

is required for understanding. The planning, instal-

lation and commissioning of the device is carried

out with the help of KNX-certied software.

Systemlink commissioning:

The function of the device is software-depend-

ent. The software is to be taken from the product

database. You can nd the latest version of the

product database, technical descriptions as well as

conversion and additional support programmes on

our website.

Easylink commissioning:

The function of the device is conguration-de-

pendent. The conguration can also be done using

devices developed specially for simple setting and

start-up.

This type of conguration is only possible with

devices of the easylink system. Easylink stands for

easy, visually supported start-up. Precongured

standard functions are assigned to the in/outputs

by means of a service module.

Functional description

The device is used to control motor-operated build-

ing ttings such as shutters and blinds via the KNX

bus. The device has 12 outputs from which each

output can be activated independently.

Correct use

- Switching electrically operated motors of 230 V

AC for blinds, shutters, awnings and similar

hangings

- Mounting on DIN rail according to DIN EN

60715 in the distribution box

Product characteristics

- independent outputs, activation via KNX bus

- Status display of the outputs on the device

- manual activation of the outputs on the device

possible, building site operation

- Position can be started directly

- 3 Alarms

- Scene function

- Forced position by higher-level controller

- Connection of various external conductors

possible

- Slat position directly controllable

Operation

Manual operation switch on/off

Bus and mains power supply are present.

zPush switch (1) to position 1/ 2.

Manual operation is switched on, the outputs

can be controlled using the operation buttons

(6) independently of each other.

1 switches on the control of the outputs

C1 C6 .. .

2 switches on the control of the outputs

C7 C12 .. .

During manual operation, the controller is deac-

tivated via the KNX bus.

Systemlink commissioning:

Depending on the programming, the manual

operation is activated permanently or for a time

period congured via the application software.

If the manual operation is blocked via the appli-

cation software, no activation takes place.

Or:

zMove switch (1) to position .auto1/auto2

The manual operation is switched off. Operation

takes place solely via the KNX bus. The output

adopts the position predened by the bus con-

troller. The switching status is displayed via the

status LED of the operation button (6).

auto 1 C1 displays the status of the outputs ..

C6.

auto 2 C7 displays the status of the outputs ..

C12.

Operating outputs in manual operation

Operation takes place per output by briey pressing

the operation button repeatedly (table1).

Status Behaviour when

button pressed briey

Output is in idle

state,

status LED of the

button (6) is off.

Movement operation starts.

Status LED of button (6)

lights up.

Output active,

status LED of the

button (6) lights

up.1)

Movement operation stops,

LED goes out.

The LED lights up red during upward travel and green

during downward travel.

Table 1: Manual operation

Information for electricians

Installation and electrical connection

DANGER!

Touching live parts can result in an

electric shock!

An electric shock can be lethal!

Disconnect the connecting cables

before working on the device and

cover all live parts in the area!

CAUTION!

Risk of destruction if parallel connec-

tion of several motors on one output!

Final position switches could fuse

together. Motors, hangings and the

device may be destroyed!

Only connect one motor per

output!

Specyfikacje produktu

Marka:	Hager
Kategoria:	nieskategoryzowany
Model:	TYM632C
Kolor produktu:	Szary
Wysokość produktu:	90 mm
Głębokość produktu:	65 mm
Zakres temperatur (eksploatacja):	-5 - 45 °C
Stopień ochrony IP:	IP20
Liczba dołączonych produktów:	1 szt.