Instrukcja obsługi Haier HPU-24H03/NAF

Haier klimatyzacja HPU-24H03/NAF

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Haier HPU-24H03/NAF (10 stron) w kategorii klimatyzacja. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.0 gwiazdek

Pobierz PDF

Strona 1/10

PACKAGED TYPE ROOM AIR CONDITIONER

OPERATION MANUAL

CONTENTS

PARTS AND FUNCTIONS

OPERATION

INSTALLATION

MAINTENANCE

2-3

4-5

6-9

The image shown here is indicative only,

The actual product may differ

English

0010564839

HPU-24H03/NAF

HNR

Parts and Functions

Indoor Unit

FRONT OUTLET

CONTROL PANEL

FRONT BOARD

LEFT&RIGHT INLET

(AIR FILTER AND PROTECTING

WIRE NET INSIDE)

LOWER INLET

(AIR FILTER AND PROTECTING

WIRE NET INSIDE)

Outdoor Unit

INLET

DRAIN HOSE

OUTLET

CONNECTING PIPING

AND ELECTRICAL WIRING

INLET

Fuzz display

COOL display

Dehu display

AMBIENT TEMP

&SET TEMP display

FAN display

HEAT display

FAN SPEED display

TURBO/QUIET

display

NEGATIVE ION

display

Sleep

display

TIMER ON/OFF

display

Loading of the battery

Loading the batteries as illustrated. 2 R-03 batteries, resetting key(cylinder)

Remove the battery cover;

Load the battery:

Be sure that the loading is in

line with the “+/-”pole request

as illustrated.

Put on the cover again

Confirm indicator

In disorderation, Reload the

batteries or load the new

batteries after 6 mins.

Note: Remove the batteries in case that unit

won’t be in usage for a long period.

If there are any display after taking-out

just need to press reset key.

Remote controller

TURBO button

COOL button

AUTO button

FAN SPEED button

TIMER button

SLEEP button

LOCK button

LIGHT button

POWER ON/OFF button

DRY button

TEMP button

SWING button

HOUR button

EXTRA FUNCTION button

CONFIRM/CANCEL button

RESET button

HEAT button

Remote controller Display

FAN display

DRY display

COOL display

MODE display

Signal sending

display

SWING display

FAN SPEED display

QUIET display

TIMER ON display&

TIMER OFF display

&SLEEP display Elec Heat display

Negative Ion display

TURBO display

TEMP display

HEAT display

NOTE: The unexplained buttons and displays is not available for the unit.

Remote controller’s operation

When in use, put the signal transmission head directly to the

receiver hole on the indoor unit.

The distance between the signal transmission head and the

receiver hole should be within 7m without any obstacle as well

Don’t throw or knock the remote controller .

When electronic-started type fluorescent lamp or change-over

type fluorescent lamp or wireless telephone is installed in the

room, the receiver is apt to be disturbedin receiving the signals,

so the distance to the indoor unit should be shorter.

NOTE

Use two same typed batteries when loading.

If the remote controller can’t run normally during

operation, please remove the batteries and reload several

minutes later.

False or unclear display during operation indicates

the batteries have been used up. please change batteries.

The waste battery should be disposed properly.

Display Board

TURBO

SLEEP



HEAT

Operation

Base Operation

Unit start

Press ON/OFF on the indoor unit ,or press ON/OFF on the

remote controller,unit starts.

The liquid crystal will display the working state of

last time (Except Timer and Sleep )

Select operation mode

Press HEAT,DRY,COOL ,or AUTO button,For each

Fan speed selection

Press FAN button. For each press,fan speed

changes as follows:

Remote controller:

LOW MED HI

AUTO

Display

circulated

Air conditioner is running under displayed fan speed.

When FAN is set to AUTO,the air conditioner automatically

adjusts the fan speed according to room temperature.

Unit stop

Press ON/OFF button, the unit stops.

Control panel display

Auto Operation

Fuzz

AUTO

COOL Operation

COOL

HIGH

DRY Operation

AUTO

Dehu

FAN Operation

LOW

FAN

HEAT Operation

HEAT

LOW

Remote controller button

Air Flow Direction Adjustment

Up and down air flow

direction display

Pos.1

Pos.2

Pos.3

Pos.4

Pos.5

Pos.1 Pos.1 Pos.1

Pos.2 Pos.2

Pos.2

Pos.3 Pos.3

Pos.3

Pos.4

Pos.5

Pos.6

Pos.7

Pos.8

Left and right air flow

direction display

Fig.1

Fig.2

Fig.3

Fig.4

(Auto swing)

Horizontal flap Vertivcal flap

Sleep Operation

Operation Mode

In COOL,DRY mode

1 hours after SLEEP mode starts, temp. will become 1

for further 6 hours then stops. Temp. is higher than temp.setting so that

room temperature won’t be too low for your sleep.

In HEAT mode

1 hours after SLEEP mode starts, temp. will become 2

for further 3 hours then stops. Temp. is lower than temp.setting so that

room temperature won’t be too high for your sleep.

In FAN mode

It has no SLEEP function.

Temp.setting

SLEEP operation starts

Rises 1

Unit stop

SLEEP operation stops

In HEAT mode

In COOL DRY mode

SLEEP operation stops

SLEEP operation starts

Temp.setting

Unit stop

Rises 1

Decreases 2

Remote controller display

Up and down air flow direction adjustment

For each press of SWING button,the position of horizontal

flap and the air flow direction on remote controller display

changes as follows according to different operation models:

COOL/DRY/FAN

HEAT/AUTO mode

Remote

controller

Horizontal

flap

Pos.1 Pos.2 Pos.3 Pos.4 Pos.5

(Fig.1)

(Fig.3)

Note:When the unit is turned off by the remote controller or the control panel,the horizontal flap will close.

When the power supply is cut off directly, the horizontal flap will not close. Please use the remote controller

or the control panel to stop the unit.Do not start or stop the operation by disconnecting the power supply

and so on

HEALTH Operation

Note:

When the HEALTH mode is set, the flap will keep the position you set.It is advisable not to keep horizontal

flap at downward positionfor a long time in COOL or DRY mode,otherwise,condensate water might occur.

Remote

controller

Vertical

flap

Pos.1 Pos.2 Pos.3 Pos.4 Pos.5 Pos.6 Pos.7 Pos.8

(Fig.2)

(Fig.4)

ć

TURBO

SLEEP

TURBO

Press button to enter additional options, when cycle display to

will flash, and then press ,enter to health function. When cancel the

function, please enter additional options again and to cancel health function.

press,operation mode changes.

Press button to enter additional options, when cycle display to

will flash. And then press , enter to Left and right air flow function.

Press . For each press, move the vertical blade by a knob on air conditioner

to adjust left and right direction referring to Fig. displays as follows:

Left and right air flow adjustment



Specyfikacje produktu

Marka:	Haier
Kategoria:	klimatyzacja
Model:	HPU-24H03/NAF
Kolor produktu:	Czarny
Rodzaj zasilania:	Prąd przemienny
Wbudowany wyświetlacz:	Nie
Wysokość produktu:	184 mm
Szerokość produktu:	105 mm
Głębokość produktu:	105 mm
Waga produktu:	900 g
Rekomendowane użycie:	Tablet/Smartphone
Technologia łączności:	Przewodowy i Bezprzewodowy
Bluetooth:	Tak
Ilość:	1
Moc wyjściowa (RMS):	- W
Port USB:	Tak
Zasilacz sieciowy:	Tak
Wi-Fi:	Nie
Przewody:	USB
Kanały wyjścia audio:	- kan.
Liczba portów USB 2.0:	1
Rodzaj baterii:	Wbudowany
Stopień ochrony IP:	IPX4
Regulacja głośności:	Cyfrowy
Konstrukcja produktu:	Cylidner
Wejście AUX:	Tak
Obsługa funkcji Plug & Play:	Tak
Złącze 3,5 mm:	Tak
Czas pracy na zasilaniu akumulatorowym:	16 h
Wbudowany mikrofon:	Tak
Uchwyty do przenoszenia:	Tak
Pasmo Bluetooth:	9 m
Cechy zabiezpieczeń:	Wodoodporny
Zestaw głośnomówiący/słuchawkowy:	Tak