Instrukcja obsługi Hayward MaxFlo VS

Hayward Przepych MaxFlo VS

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hayward MaxFlo VS (36 stron) w kategorii Przepych. Ta instrukcja była pomocna dla 14 osób i została oceniona przez 7.5 użytkowników na średnio 4.8 gwiazdek

Pobierz PDF

Strona 1/36

IS23520VSP Rev-D

IS23520VSP Rev-D IS23520VSP Rev-D

Hayward Pool Products

620 Division St, Elizabeth, NJ 07207

Phone: (908) 355-7995

www.hayward.com

www.hayward.com www.hayward.com

MaxFlo VS™ 500

Owner’s Manual

Model SP23520VSP

MaxFlo VS 500 Variable Speed Pump

Hayward’s MaxFlo VS 500 variable speed pump delivers incredible energy savings via its advanced

hydraulic design combined with a totally enclosed, permanent magnet motor. MaxFlo VS 500 is easily

installed either as a programmable stand-alone pump or with a Hayward or third party controller and

features an easy-to-use digital control interface that can be mounted in four different positions on the

pump or removed and mounted on the wall for total user convenience.

Note: To prevent potential injury and to avoid unnecessary service calls, read this manual carefully and

completely. Unless otherwise stated, instructions in this manual apply to both pump models.

SAVE THIS INSTRUCTION MANUAL

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Page 2 of 36 MaxFlo VS 500 Pump

MaxFlo VS 500 Pump

MaxFlo VS 500 Pump MaxFlo VS 500 Pump IS23520VSP Rev-D

Table of Contents

1.IMPORTANT SAFETY INSTRUCTIONS ................................................................................................................. 4

2.General Information ........................................................................................................................................ 7

2.1.Introduction 7

2.2.Primary Features 7

2.3.Product Dimensions 7

3.Energy Efficiency Overview .............................................................................................................................. 8

4.Installation and Wiring .................................................................................................................................... 8

4.1.Pump Location 8

4.2.Pump Mounting 9

4.3.Pipe Sizing Chart 9

4.4.Plumbing 9

4.5.Electrical 10

4.6.Electrical Specs 10

4.7.Voltage 10

4.8.Grounding and Bonding 10

4.9.Wiring 10

4.10.Remote Control Wiring/Operation 11

4.11.Digital Control Interface Orientation 11

4.12.Interface Wall Mounting 12

4.13.Installation Procedure 14

5.Wiring Diagrams ........................................................................................................................................... 15

5.1.Input Power Wiring (Required) 15

5.2.Wall Mounted Digital Control Interface Wiring (Optional) 15

5.3.External Relay Speed Control Wiring (Optional, for remote selection of pump speed) 16

5.4.Hayward Automation Control Wiring (Optional, for remote control of pump speed) 17

5.5.Remote Stop Switch Wiring (Optional) 18

6.Startup & Operation ...................................................................................................................................... 18

6.1.Prior to Start-Up 18

6.2.Starting/Priming the Pump 19

6.3.User Interface Summary 20

6.4.Menu Outline 21

6.5.Initial startup 21

6.6.Configuration Menu 22

6.7.Timer Menu 23

6.8.Preset Speed Setup Menu 24

6.9.Diagnostic Menu 24

6.10.Stop/Resume 25

6.11.Quick Clean 25

6.12.Remote Stop 26

7.Maintenance ................................................................................................................................................ 26

8.Storage / Winterization ................................................................................................................................. 26

8.1.Storing Pump For Winterization 26

9.Shaft Seal Change Instructions ..................................................................................................................... 27

9.1.Removing the Motor Assembly 27

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Page 3 of 36 MaxFlo VS 500 Pump

MaxFlo VS 500 Pump

MaxFlo VS 500 Pump MaxFlo VS 500 Pump IS23520VSP Rev-D

9.2.Removing the Impeller 27

9.3.Removing the Ceramic Seat 27

9.4.Seal Installation 27

9.5.Replacing the Impeller and Diffuser 27

9.6.Replacing the Motor Assembly 28

10.Replacement Parts ........................................................................................................................................ 28

10.1.Parts Diagram 28

10.2.Parts Listing 29

11.Troubleshooting ........................................................................................................................................... 30

11.1.General Problems 30

11.2.Check System Messages 32

12.Warranty ....................................................................................................................................................... 33

13.Product Registration ..................................................................................................................................... 33