Instrukcja obsługi Heatit Z-WATER2
Heatit
Niesklasyfikowane
Z-WATER2
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Heatit Z-WATER2 (5 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 5 użytkowników na średnio 4.8 gwiazdek
Strona 1/5
1. INTRODUCTION
Heatit Z-Water2 is a DIN-rail regulator for controlling
waterbased heating systems. The module clips right onto a
DIN-rail and allows you to control your waterbased heating
through your Z-Wave™ network.
Heatit Z-Water2 is equipped with 9 potential free relays for
actuators. It also has 2 analog inputs for temperature sensors.
The Heatit Z-Water2 relays may be controlled by associations
with other Z-Wave thermostats e.g Heatit. Each relay can
control one or several actuators in your underfloor heating
system.
2. STATEMENT REGARDING PRODUCTS FROM MULTIPLE
MANUFACTURERS
Please read this before installation
This device may be used with all devices certified with the
Z-Wave Plus™ certificate and should be compatible with
such devices produced by any manufacturer. Every primary
controller is dierent depending on the manufacturer, their
target audience and intended use/application. Please review
the functionalities implemented by the primary controller you
intend to use with our Z-Wave Plus certified device to ensure
that it provides the necessary controls to take full advantage of
our product’s capabilities.
3. BEHAVIOR WITHIN THE Z-WAVE NETWORK
This device may be operated within any Z-Wave™ network
with Z-Wave-certified devices from other manufacturers. All
non-battery-operated nodes within the network will act as
repeaters regardless of manufacturer to increase the reliability
of the network. On delivery, the device does not belong to any
Z-Wave network. The device needs to be added to an existing
network to communicate with the other devices within it.
Devices may also be removed from a network. The add/
remove processes are initiated by the primary controller of the
Z-Wave network.
4. INSTALLATION GUIDELINES
Installation must be done by a qualified electrician in
accordance with national building codes. Before installation,
disconnect the power to the device from the mains. During
installation of the device, power to the device must be
disconnected AT ALL TIMES!
Max tightening torque for terminal screws: 2Nm
Use the following procedure to install Heatit Z-Water2:
1. Place the top part of the DIN rail mounting on the Heatit
Z-Water2 over the top of the DIN rail so it hooks onto the
rail.
2. Use a flathead screwdriver to push the DIN rail mounting tab
downward.
3. Tilt the bottom of the Heatit Z-Water2 until it touches the
DIN rail. Now let go of the DIN rail mounting tab so it locks
into place.
4. Make all the necessary connections to the device (max
tightening torque for all screw terminals is 2Nm). Apply
power to the device after all connections have been made.
TABLE OF CONTENTS
1. Introduction
2. Statement regarding products from multiple
manufacturers
3. Behaviour within the Z-Wave network
4. Installation guidelines
5. Connections
6. Quick Start
7. Add/Remove
7.1 Method 1: Standard (Manual)
7.2 Method 2: SmartStart (Automatic)
8. Factory Reset
9. Startup
10. LED blinking patterns description
11. QR-Code Placement (DSK)
12. Security
13. Node Information Frame
14. Associations
14.1 Setting and Removing Associations
15. Association Groups
16. Configuration Parameters
17. Calibration
18. Command Classes
18.1 Basic Command CLass
18.2 Binary Switch Command Class
18.3. Multilevel Sensor Command Class
18.4. Indicator Command Class
19. Supported Command Classes
20. Other features
21. Dimensions
22. External antenna connector
Product info
HEATIT
Z-WATER2
Installers manual
Firmware version Document version
FW 1.0 2023-A
Article no. Document date
45 124 95 01.05.2023
Org. doc. date 01.05.2023
TO PRODUCT
DOCUMENTS
Specyfikacje produktu
| Marka: | Heatit |
| Kategoria: | Niesklasyfikowane |
| Model: | Z-WATER2 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Heatit Z-WATER2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Heatit
7 Października 2024
7 Października 2024
28 Września 2024
28 Września 2024
28 Września 2024
15 Września 2024
14 Września 2024
4 Września 2024
Instrukcje Niesklasyfikowane
- BT
- Dometic
- Winia
- EWT
- MaximaVida
- Rinnai
- Yeastar
- FireKing
- Empress Effects
- Clage
- Cuggl
- Musser
- Lauten Audio
- Ordo
- Petkit
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025