Instrukcja obsługi Hikvision DS-2TD1217-2/P

Hikvision kamera bezpieczeństwa DS-2TD1217-2/P

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hikvision DS-2TD1217-2/P (3 stron) w kategorii kamera bezpieczeństwa. Ta instrukcja była pomocna dla 66 osób i została oceniona przez 33.5 użytkowników na średnio 4.6 gwiazdek

Pobierz PDF

Strona 1/3

The Polaris MiniJet for vinyl liner pools (FFMJ-VL) is

designed to mount in a vinyl pool wall slightly above

water level. It can be mounted in wall panels with a

thickness of .1094” (12Ga. Steel) to 3/8” (polymer

wall). For deck installations, use the standard Polaris

MiniJet (FFMJ).

Preparing For Installation

Determine the mean water level of the pool and

the vertical center line of each MiniJet. If water

covers the nozzle, the performance will be affected.

Mounting it too high may interfere with the coping

and liner installation.

Pressure testing is required. Screw the 3/8” plug

provided into the nozzle inlet of the MiniJet housing.

This plug is also used for winterizing, so do not

discard.

Store the brass jets, the MiniJet housing cover, the

3/8” plug and the four screws for pool start-up.

Prevent dirt and debris from entering the plumbing

lines during construction.

Installing The MiniJet

1. Position the Layout Template to line up with the

vertical center line and mean water level. Tape it to

the pool wall.

2. Use a 1/4” bit to drill fourteen (14) mounting holes.

3. Use a 3/8” bit to drill the four (4) corner holes used

as guides for cutting out the center square.

4. Use a jigsaw and blade compatible with the

material of the pool wall to cut out the center

square, cutting around the outer edges of the four

(4) holes.

5. Insert the MiniJet housing through the wall from

the water side. Rest the back of the housing flange

against the inside of the pool wall.

6. Position the rear mounting plate over the back of

the MiniJet housing on the outside of the pool wall.

Insert the two (2) pan-head screws in the center

holes (top and bottom) of the flange, through the

pool wall and into the rear mounting plate. Secure

housing to pool wall.

MiniJet® for Vinyl Liner

Pool Installation

Plumbing The MiniJet

Water flow and pressure control the projection of the

water. As a rule, 4.4 GPM per nozzle will provide

adequate water flow. Refer to data below.

MiniJet Performance Data Chart

Height of

Jet Spray 3.3’ 6.6’ 9.8’ 13.1’

Feet

of Head 3.9’ 7.9’ 11.9’ 16.0’

GPM 2.1 3.0 3.7 4.4

1. Determine the size of the manifold or plumbing

loop and return pipe required.

MiniJet Pipe Sizing

Max.

MiniJets

Return

Pipe Sizing

Suction

Pipe Size

8 1-1/2” 1-1/2”

12 2” 2”

16 2-1/2” 2-1/2”

26 3” 3”

2. Use 1/2” PVC pipe to connect the MiniJet to the

manifold or plumbing loop. See plumbing diagram

below.

Optional

Loop

Extend Past Last

MiniJet 5' Minimum

MiniJet

Manifold Pipe

Valve

Riser

From

Pump

See Chart for

Proper Sizing

3. When the MiniJets are lined up to project water

streams of equal distance, cut the riser to equal

lengths. When the MiniJets are not set in lines

parallel to the pool ledge, valve each MiniJet

separately.

Specyfikacje produktu

Marka:	Hikvision
Kategoria:	kamera bezpieczeństwa
Model:	DS-2TD1217-2/P
Podręcznik użytkownika:	Tak
Technologia łączności:	Przewodowa
Formaty kompresji:	H.264, H.265
Przeznaczenie:	Zewnętrzna
Ilość portów Ethernet LAN (RJ-45):	1
Przewodowa sieć LAN:	Tak
Rodzaj interfejsu sieci Ethernet:	Fast Ethernet
Obsługiwane protokoły sieciowe:	IPv4/IPv6, HTTP, HTTPS, 802.1x, Qos, FTP, SMTP, UPnP, SNMP, DNS, DDNS, NTP, RTSP, RTCP, RTP, TCP, UDP, IGMP, ICMP, DHCP, PPPoE
Kodeki glosu:	G.711, G.722.1, G.726, MP2L2, PCM
Typ przetwornika obrazu:	CMOS
Min. Oświetlenie:	0.003 lx
Filtrowanie adresów IP:	Tak
Wielkość czujnika CCD:	1/2.7 "
Skanowanie progresywne:	Tak
Szybkość migawki:	1/100 s
Inkrypcja HTTS:	Tak
Transmisja wideo:	Tak
Przeglądarka internetowa:	Tak
Liczba języków:	32