Instrukcja obsługi Hikvision DS-PD2-P25-W
Hikvision
czujnik ruchu
DS-PD2-P25-W
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hikvision DS-PD2-P25-W (4 stron) w kategorii czujnik ruchu. Ta instrukcja była pomocna dla 21 osób i została oceniona przez 11 użytkowników na średnio 4.7 gwiazdek
Strona 1/4
DS-PD2-T12P-WEL
12m Wireless Outdoor Detector
Detecon Range
EN50131-2-2:2008
EN50131-1:2006+A1:2009
Security Grade (SG)2
Environmental Class(EC)II
DS-PD2-P25-W
25m Wireless Long Range Corridor PIR Detector
Diagram References
E N G L I S H
1
2
3
4
For electrical products sold within the European
Community. At the end of the electrical products
life, it should not be disposed of with household
waste. Pleaserecycle where facilies exist.
Check with your local Authority or retailer for
recycling advice in your country.
Lens Characteriscs
25m
90°
46 zones and 6 planes
0.3–3m/s
1.8-2.4m
Yes
Yes
Yes
Front, rear, and bracket tamper signal input
Yes
868MHz, FM transceiver
800m
1x CR123A
2
-10°C to +40°C(Cerfied)
125g
117 x 69 x 50mm
Yes
Yes
Detecon Range
Detecon Angle
Detecon Zones
Detecon Speed
Mounng Height
Creep-zone Protecon
Blue Wave Technology
Digital Temperature Compensaon
Tamper Protecon
Signal Strength Indicators (SSI)
Transmission Frequency
Range in Open Space
3V Lithium Baery Included
Minimum Baery Life (years)
Operaon Temperature
Weight
Dimensions(H x W x D)
Ceiling mounted bracket included
Wall mounted bracket included
Electrical & baery
Environment Features
Accessories
Key Features
Technical Specification
Battery Information
2
1
3
4
A
BC
CEILINGBRACKET
+
-
>5s
+
-
REGISTRATION
+
-
5s
+
-
LED ON LED OFF
LOW
HIGH
+
+
+
+
+
+
+
+
CR123A
LITHIUM -
HIGH
LOW
TAMPER =
=
REGISTRATION
BRACKET TAMPER
SEE SECTION4
A
B
EC
D
WALLBRACKET
REAR TAMPER
BREAK-OUT
Wireless device control
Registration
Please register the device within 90 seconds aer it being powered on.
Register Locally
1.Make the security control panel enter the registraon mode.
2. Register the detector: Hold the registraon key unl the three LEDs
flash alternately. The green LED will flash 8 mes if the registraon is
finished.
3. Communicaon Test: Release the TEMPER spring to trigger the alarm.
Note: The distance between the security control panel and the detector
should be less than 50 cm.
Initialize the Detector
1. Remove the baery to power the detector off.
2. 5s later, hold the registraon key and reinstall the baery to power
the detector on at the same me to make the three LEDs start flashing
alternately. Release the registraon key while the three LEDs flash once
together. If you disable the detector’s LEDs, you can remotely enable
them in walk tests.
Diagnostics(Check Signal Strength before mounting)
Wired tamper and brackets
This product and - if applicable - the supplied accessories too are marked
with "CE" and comply therefore with theapplicable harmonized European
standards listed underthe RE Direcve 2014/53/EU, the RoHS Direcve
2011/65/EU.
The baeries supplied have been chosen to provide long service life whilst,
for safety reasons, having limited output current.The baery is protected
on purchase by a piece of plasc that must be removed for operaon.
When disposing of the product, the baery must be removed and disposed
of separately in accordance with the local regulaons.
Specyfikacje produktu
| Marka: | Hikvision |
| Kategoria: | czujnik ruchu |
| Model: | DS-PD2-P25-W |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Hikvision DS-PD2-P25-W, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje czujnik ruchu Hikvision
5 Kwietnia 2025
Instrukcje czujnik ruchu
Najnowsze instrukcje dla czujnik ruchu
8 Kwietnia 2025
8 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
27 Marca 2025
27 Marca 2025
5 Marca 2025
5 Marca 2025