Instrukcja obsługi Hobart 6801
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hobart 6801 (12 stron) w kategorii Maszyna do piłowania. Ta instrukcja była pomocna dla 18 osób i została oceniona przez 9.5 użytkowników na średnio 4.9 gwiazdek
Strona 1/12
FORM 34405 Rev. C (August 2011)
MODEL 6801 MEAT SAW
MODEL
6801 ML-134094
PREVIOUS MODELS COVERED BY THIS MANUAL:
6801 ML-104948
701 S. RIDGE AVENUE
TROY, OHIO 45374-0001
937 332-3000
www.hobartcorp.com
– 2 –
Installation, Operation, and Care of
MODEL 6801 MEAT SAW
SAVE THESE INSTRUCTIONS
GENERAL
The 6801 Meat Saw is rugged, durable, and easy to clean. The saw is equipped with a water resistant
3 HP electric motor and direct gear drive transmission. The carriage (Fig. 1) has stainless steel ball
bearings providing easy travel and dependability. The shaped front edge of the carriage is comfortable to
the operator's body even when leaned on during movement. The carriage lock is standard.
Table, carriage, pulleys, guides, and wiper assemblies can be quickly removed without tools for ease of
cleaning. Moving parts are enclosed but accessible. The blade is guarded above and below the cutting
zone. The pusher plate is provided to eliminate the need of handling items close to the blade; it can ride
on the right "anged-end" of the carriage so you keep your hands away from the cutting edge of the blade.
For electrical specications above 250 volts, a transformer provides a 115 volt control circuit voltage.
Thermal overload protection is an option.
One long-life blade is furnished with each saw as standard equipment. This blade cannot be re-sharpened;
replacement blades are available through your local Hobart Service Ofce.
© HOBART, 1995, 2000
PL-41385-1
UPPER PULLEY COVER (SST)
COLUMN GUARD
GAUGE PL EAT
TABLE (RIGHT)
GAUGE PL E HANDLEAT
LOCK LEVER
LOWER COVER (SCRAP N)PA
LEGS
FEET
CARRIAGE LOCK
CARRI EAG
TABLE (LEFT) SAW BLADE
UPPER GUIDE AND GUARD
SWITCH KNOB
Fig. 1
– 3 –
INSTALLATION
UNPACKING AND ASSEMBLY
Immediately after unpacking the meat saw, check for possible shipping damage. If the meat saw is found
to be damaged, save the packaging material and contact the carrier within 15 days of delivery.
Prior to installation, test the electrical service to make sure it agrees with the specications on the machine
data plate located on the column.
Packed in a packet attached to the table compartment are the pusher plate and the gauge plate handle.
Place the pusher plate in its storage location under the carriage support (Fig. 2). Assemble the gauge
plate handle to the gauge plate support by screwing the stud into the threaded hole (Fig. 3).
LEVELING
Place the saw in its operating location. Using a spirit level, level the meat saw front-to-back and side-to-
side by turning the threaded feet in or out.
PL-52107
Hand Knob
Upper Guide
and Guard
PL-41386-1
HAND KNOB
CARRIAGE
SUPPORT
SAW BLADE
CARRI EAG
PUSHER PL EAT
PL-41387-1
GAUGE PL E HANDLEAT
Fig. 2 Fig. 3
Fig. 4
Disconnect the electrical power to the machine and follow lockout / tagout
procedures.
SAW BLADE
The saw blade must be installed so the teeth point to the right and
down (Fig. 4).
UPPER GUIDE AND GUARD ASSEMBLY
When the saw is off, the hand knob (Fig. 4) can be used to raise or lower
the upper guide and guard assembly so the cutting zone is only as high
as necessary for the piece being cut. The hand knob is not loosened
during raising or lowering — it should remain tightly secure.
Specyfikacje produktu
| Marka: | Hobart |
| Kategoria: | Maszyna do piłowania |
| Model: | 6801 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Hobart 6801, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Maszyna do piłowania Hobart
25 Września 2024
25 Września 2024
Instrukcje Maszyna do piłowania
- Maszyna do piłowania Batavia
- Maszyna do piłowania Bruder Mannesmann
- Maszyna do piłowania Dremel
- Maszyna do piłowania Bestgreen
- Maszyna do piłowania McCulloch
- Maszyna do piłowania Elu
- Maszyna do piłowania Kress
- Maszyna do piłowania HiKOKI
- Maszyna do piłowania Toolson
- Maszyna do piłowania Toolcraft
- Maszyna do piłowania Lionelo
- Maszyna do piłowania Garland
- Maszyna do piłowania Hitachi
- Maszyna do piłowania MyTool
- Maszyna do piłowania Wolfcraft
Najnowsze instrukcje dla Maszyna do piłowania
3 Kwietnia 2025
3 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
29 Marca 2025