Instrukcja obsługi Honeywell 5804BD
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Honeywell 5804BD (2 stron) w kategorii Kontroler. Ta instrukcja była pomocna dla 24 osób i została oceniona przez 12.5 użytkowników na średnio 4.7 gwiazdek
Strona 1/2
N8547V1 04/09
5804BD
TWO-WAY WIRELESS KEY
USER GUIDE
About 5804BD
5804BD is a four-button remote control for your alarm system. 5804BD can send a command to the alarm system,
such as to arm or disarm, as well as receive system status. Two LEDs and a speaker are used to indicate system
status. 5804BD is typically used for arming, disarming, and controlling devices. Check with your installer to
understand which functions the buttons have been assigned on your unit.
Operating the Buttons
Activating a Button
To activate a function, press and hold the appropriate button down until the yellow LED flashes (2 beeps will be
heard), and then release it.
NOTE: Transmission will not be successful if the key is not within range of the system’s receiver. If 5804BD does
not receive system status from the panel for approximately five seconds, it will generate a long (one second) beep.
Requesting System Status
You can check system status before arming or disarming your system.
Check the system status by momentarily pressing and releasing any button. The yellow LED will flash after you
release the button (one beep will be heard). After a second or two, the device will display the system status
through the LEDs and speaker (see the System Status Indications Table, below). If 5804BD does not receive
system status from the panel for approximately five seconds, it will generate a long (one second) beep and shut
itself down. It will also shut itself down if you do not press a button within five seconds of receiving a status update.
System Status Indications Table
LED LED Condition Sounds System Status
On Steady 2 Beeps Armed Away or Maximum
On Steady 3 Beeps Armed Stay or Instant
Flashing Pulsing Fire Alarm in progress
Flashing Steady Armed, Burglary Alarm in progress
Red
Flashing Silent Alarm Memory
Yellow (right) Flashing Silent Indicates RF transmission
Red & Green Alternately Flashing Silent In Enter House ID Mode
On Steady 1 Beep Disarmed, Ready to Arm
Flashing Silent Disarmed, Not Ready to Arm
Flashing Pulsing System in Trouble Condition
Green
Flashing 1 Beep System Not Ready
Multiple Button Operations
The 5804BD can generate the same responses as
keypad key pairs of [*] + [#] and [*] + [1] by
depressing “A” + “C” and “B” + “D”
button pairs,
respectively.
You must depress the button pair for
at least 2 seconds for the 5804BD to reco
gnize the
button pair command. These button pairs
allow you
to activate additional keypad functions
depending
on control panel programming. Check with
your
installer to understand which functions the buttons
have been assigned on your unit.
Specyfikacje produktu
| Marka: | Honeywell |
| Kategoria: | Kontroler |
| Model: | 5804BD |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Honeywell 5804BD, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Kontroler Honeywell
5 Września 2024
25 Sierpnia 2024
15 Sierpnia 2024
4 Lipca 2024
Instrukcje Kontroler
- Eurolite
- Heath Zenith
- Dangerous Music
- Boss
- Radial Engineering
- Krom
- Apart
- Samsung
- Intel
- Cisco
- Apricorn
- Morningstar
- Heritage Audio
- Sweex
- Dragonshock
Najnowsze instrukcje dla Kontroler
2 Kwietnia 2025
30 Marca 2025
30 Marca 2025
30 Marca 2025
30 Marca 2025
30 Marca 2025
28 Marca 2025
27 Marca 2025
26 Marca 2025
2 Marca 2025