Instrukcja obsługi Honeywell Lyric T6

Honeywell termostat Lyric T6

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Honeywell Lyric T6 (19 stron) w kategorii termostat. Ta instrukcja była pomocna dla 14 osób i została oceniona przez 7.5 użytkowników na średnio 4.6 gwiazdek

Pobierz PDF

Strona 1/19

Package Includes:

• Lyric T6 PRO WiFi Thermostat

• UWP Mounting System

• Honeywell Standard Installation

Adapter (J-box adapter)

• Honeywell Decorative Cover Plate –

Small; size 449/64 in = 121mm.

• Screws and anchors

• Professional Install Guide

• Getting Started Guide

*TH6320WF2003 depicted. Other models may vary.

Lyric™ T6 Pro Wi-Fi

Programmable Thermostat

Professional Install

Guide

33-00153-0

Compatibility

• Compatible with most heating, cooling, and heat pump systems

• Required: 24 VAC power (“C” wire)

• Does not work with electric baseboard heat (120240V)

• Does not work with millivolt systems

• Android or iOS smartphone or tablet

Customer assistance

WEB customer.honeywell.com

PHONE 18006333991

UWP Mounting System installation

1. Open package to find the UWP. See

Figure 1.

2. Position the UWP on the wall. Level and

mark hole positions. See Figure 2.

Drill holes at marked positions, and

then lightly tap supplied wall anchors

into wall using a hammer.

‒Drill 7/32” holes for drywall.

3. Pull the door open and insert wires

through wiring hole of the UWP. See

Figure 3.

4. Place the UWP over the wall anchors.

Insert and tighten mounting screws

supplied with the UWP. Do not

overtighten. Tighten until the UWP

no longer moves. Close the door. See

Figure 4.

Optional Decorative Cover Plate installation

Use the Optional Cover Plate when:

• Mounting the thermostat to an

electrical junction box

• Or when you need to cover paint gap

from the old thermostat.

5. Separate the Junction Box Adapter

from the Cover Plate. See Figure 5.

6. Mount the Junction Box Adapter to

the wall or an electrical box using any

of the eight screw holes. Insert and

tighten mounting screws supplied with

Cover Plate Kit. Do not overtighten.

Make sure the Adapter Plate is level.

See Figure 6.

7. Attach the UWP by hanging it on the

top hook of the Junction Box Adapter

and then snapping the bottom of the

UWP in place. See Figure 7.

8. Snap the Cover Plate onto the

Junction Box Adapter. See Figure 8.

Use 3x supplied

screws #8 1-1/2”

Use 2x

supplied

screws

#6 5/8”

Terminal designations

Conventional Systems Heat pump systems

Terminal Description Terminal Description

S/S Universal input for a wired

indoor, outdoor sensor S/S Universal input for a wired

indoor, outdoor sensor

Y Compressor Stage 1 Y Compressor Stage 1

Y2 Compressor Stage 2 Y2 Compressor Stage 2

G Fan Relay G Fan Relay

24VAC Common wire from

secondary side of cooling

transformer (if 2 transformers)

24VAC Common wire from

secondary side of cooling

transformer

K* Connect to K on Wire Saver

Module K* Connect to K on Wire Saver

Module

U/U** Universal relay for ventilation U/U** Universal relay for ventilation

A L/A Connect to compressor

monitor

W Heat Stage 1 O/B Changeover valve for heat

pumps

W2 Heat Stage 2 Aux Backup Heat

E Emergency Heat

R 24 VAC Heating transformer R 24 VAC Heating transformer

Rc 24 VAC Cooling transformer Rc 24 VAC Cooling transformer

* The THP9045A1023 Wire Saver Module is used on heat/cool systems when you only have four wires

at the thermostat and you need a fifth wire for a common wire. Use the K terminal in place of the Y and

G terminals on conventional or heat pump systems to provide control of the fan and the compressor

through a single wire—the unused wire then becomes your common wire. See THP9045 instructions

for more information.

** Ventilation is not available on all models. When the U slider is in the down position (2 wires), the U

contacts are a dry set of contacts. If your ventilation system requires 24 volts, move the U slider to the

up position (1 wire). Lower U terminal is internally jumped to the Rc terminal. In this application, you

would hook up one wire from your damper to the upper U terminal and the other to the common side of

the transformer.

Wiring UWP

Push down on the tabs to put the wires into the inner holes of their corresponding termi nals

on the UWP (one wire per terminal) until they are firmly in place. Gently tug on the wires to

verify they are secure. If you need to release the wires again, push down the terminal tabs

on the sides of the UWP.

This wiring is just an example,

yours may vary.

Specyfikacje produktu

Marka:	Honeywell
Kategoria:	termostat
Model:	Lyric T6
Kolor produktu:	Czarny
Typ kontroli:	Dotyk
W zestawie pilot zdalnego sterowania:	Nie
Typ ekranu:	LCD
Podświetlenie:	Tak
Podświetlenie wyświetlacza:	Tak
Funkcja pamięci:	Nie