Instrukcja obsługi Honeywell Performance HBW4PGR1
Honeywell
Kamera monitorująca
Performance HBW4PGR1
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Honeywell Performance HBW4PGR1 (3 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 19 osób i została oceniona przez 10 użytkowników na średnio 4.4 gwiazdek
Strona 1/3
HBW4PGR1 WDR 4MP IR Bullet Camera
Quick Installation Guide
Thank you for purchasing a Honeywell Performance Series IP camera.
Follow the instructions in this guide to install and log in to your camera
For instructions on configuring the camera, refer to the user guide on t
CD that came with your camera. If you require additional assistance, ca
the number listed for your region on the back cover.
Cautions and Warnings
WARNING To ensure compliance with electrical safety standards, this product is
intended for use with a Listed Power Adapter marked “Limited Power
Source” or “LPS” on the unit, output rated to 12 VDC, minimum 0.33 A,
TMA=60 deg C, or from Power over Ethernet (PoE) provided by Listed
Information Technology Equipment meeting IEEE 802.3af PoE standard.
CAUTION
The Ethernet connection is not intended to be connected to exposed
(outside plant) networks. Do not connect two power sources to the camera
at the same time.
CAUTION
Invisible LED radiation (850 nm). Avoid exposure to beam.
Important Safeguards
• Read and keep these instructions.
• Confirm the installation surface can support at least three times the weight of the camera.
• Do not aim the camera toward a bright light source for extended periods to prevent damage to the imager.
• Avoid operating the unit under or close to unstable light sources (may cause flickering), or close to fluorescent
lamps or objects reflecting light.
• D o not touch the camera lens.
• Do not drop the camera or subject it to physical shock.
• Do not use a strong or abrasive detergent when cleaning the camera.
• Avoid operating or storing the unit in extremely humid, dusty, hot/cold environments, where the operating
temperature is outside the recommended range of -22°F to 140°F (–3 0°C to 60°C).
• Do not apply power to the camera before completing installation.
Before You Begin
Before you begin, check that you have received all of the parts listed below. If any parts are missing or damaged,
contact your dealer immediately.
• Camera
• Installation CD
• Quick installation guide
• Allen key (L-wrench)
•
Self- tapping screws (×4)
• Plastic wall anchors (×4)
• Mounting template
CAUTION Installation and servicing should be performed only by qualified and experienced technicians to conform
to all local codes and to maintain your warranty.
Preparing the Mounting Surface
1. Apply the mounting template to the mounting surface.
Note Observe the orientation of the cable exit notch on the bracket base. In outdoor the notch installations,
should point downward to prevent water from entering the camera housing.
2. Using the mounting template as a guide, drill pilot holes in the mounting surface, then hammer the supplied four
anchors into the holes.
3. Drill a cable entry hole in the mounting surface, then pull the required cables through the hole.
Mounting and Aiming the Camera
1. If you are using a microSD card with the camera, install it before continuing. To access the microSD card slot,
remove the panel m mon the underside of the camera and insert a icroSD card into the icroSD card slot (refer to
the picture below).
Note Press and hold the reset button abouts 10s when the camera is power on or rebooting to restore the
default settings, including the user name, password, IP address, port NO., ect.
2. Connect one end of the Ethernet cable to the RJ-45 port on the
camera.
3. If the other end of the Ethernet cable is NOT connected to a PoE
switch or NVR, connect the power connector of the camera to a 12
VDC power source.
4. If the camera is installed outdoor, you can adapt the water- proof
accessory for the network cable after the camera is secured on the
installation surface refer to the picture ( on the right).
5. Attach the camera assembly to the mounting surface using the
supplied screws.
CAUTION
THIS SYMBOL INDICATES THAT
DANGE OUSR VOLTAGE
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT
WITHIN THE UNIT.
CA : TUTION O REDUCE THE RISK OF ELECTRIC
SHOCK, DO N T REM THE CO OVE OVER.
NO USER-SERVICEABLE PAR .TS INSIDE
REFER SER TO QU RVICING ALIFIED SE VICE
PERSONNEL.
THIS SYMBOL INDICATES THAT
IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS
ACCOMPANY THIS UNIT.
RISK OF ELECTRIC
SHOCK
DO N T OPENO
Specyfikacje produktu
| Marka: | Honeywell |
| Kategoria: | Kamera monitorująca |
| Model: | Performance HBW4PGR1 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Honeywell Performance HBW4PGR1, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Kamera monitorująca Honeywell
21 Grudnia 2024
21 Grudnia 2024
23 Września 2024
19 Września 2024
14 Września 2024
13 Września 2024
11 Września 2024
10 Września 2024
10 Września 2024
10 Września 2024
Instrukcje Kamera monitorująca
Najnowsze instrukcje dla Kamera monitorująca
28 Stycznia 2025
25 Stycznia 2025
17 Stycznia 2025
17 Stycznia 2025
15 Stycznia 2025
13 Stycznia 2025
13 Stycznia 2025
13 Stycznia 2025
12 Stycznia 2025
12 Stycznia 2025