Instrukcja obsługi Hotpoint H8I HT59 LS UK
Hotpoint
Pomywaczka
H8I HT59 LS UK
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hotpoint H8I HT59 LS UK (6 stron) w kategorii Pomywaczka. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 3.5 użytkowników na średnio 4.5 gwiazdek
Strona 1/6
EN
1
Daily Reference Guide
THANK YOU FOR BUYING A HOTPOINT PRODUCT. In order
to receive a more complete assistance, please register your
appliance on: www.hotpoint.eu/register
Before using the appliance carefully read
Safety and Installation Instructions. More information about your
product available on website: docs.hotpoint.eu
After installation, please remember to remove all transport
protection parts from the dishwasher.
CONTROL PANEL
1. ON-OFF/Reset button with indicator light
2. Eco program button with indicator light
3. Rapid program Soak program button with indicator light/ - 3 sec. press
4. Delicates program button with indicator light/ - 3 sec. pressSelf-Clean program
5. Auto programs buttons with indicator lights - Auto Intensive 65°/ Auto Mixed 55°/
Auto Fast 50°
6. Salt reservoir empty indicator light
7. Rinse Aid reservoir empty indicator light
8. Display
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
9. Program number remaining time and indicator
10. Closed water tap indicator light
11. DESCALE indicator light
12. Extra options buttons Half Load / Silent / Sani Rinse with indicator lights -
13. Zone Wash 3D option button with indicator light
14. Extra Dry option button with indicator light / Settings - 3 sec. press
15. Delay option button with indicator light
16. START/Pause button with indicator light
FIRST TIME USE
SETTING MENU
1. Switch on the appliance by pressing the button.ON-OFF
2. Hold the Settings (Extra Dry ) button for 3 seconds, until you hear a
beep and the display shows „ ”.SEt
3. After one second the rst available setting (letter „ ”) will be displayed.h
4. Press Auto programs /Extra options buttons to scroll through the list
of available settings (see table below), then press START/Pause to
view and change the value of the currently selected setting.
5. Press Auto programs /Extra options to change the value, then press
START/Pause to save the new value.
6. To change another setting, repeat points 2 and 5.
7. Press or wait 30 seconds to exit the menu.ON-OFF
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and on
the machine’s functional components.
The salt reservoir is located in the lower part of the dishwasher (under the
lower rack on the left side).
• It is mandatory that THE SALT RESERVOIR NEVER BE EMPTY.
• It is important to set the water hardness.
• Salt must be lled when the SALT REFILL indicator light on the con-
trol panel is lit.1. Remove the lower rack and unscrew the reservoir cap
(anticlockwise).
2. Position the funnel and ll the salt reservoir (see gure)
right up to its edge (approximately 0,5 kg); it is not un-
usual for a little water to leak out.
3. Only the rst time you do this: ll the salt reservoir
with water.
4. Remove the funnel and wipe any salt residue away from the opening.
Make sure the cap is screwed on tightly so that no detergent can get into
the container during the wash program (this could damage the water
softener beyond repair).
Run a program every time as soon as you completed relling the salt
reservoir to avoid corrosion.
Setting the water hardness
To allow the water softener to work in a perfect way, it is essential that the water
hardness setting is based on the actual water hardness in your house. This in-
formation can be obtained from your local water supplier. The factory setting is
“3”. See „WATER HARDNESS TABLE”. To change, follow instructions in section
“SETTING MENU”.
Only use salt that has been specically designed for dishwashers.
After the salt has been poured into the machine, the SALT REFILL indicator
light switches o.
If the salt container is not lled, the water softener and the heating
element may be damaged as a result of limescale accumulation.
Use of salt is recommended with any type of dishwasher detergent.
LETTER SETTING VALUES
(Default - )in bold
Water Hardness Level
(see “SETTING THE WATER HARDNESS”
and “WATER HARDNESS TABLE”) 1 | 2 | | 4 | 53
Rinse Aid Level
(see “ADJUSTING THE DOSAGE OF RINSE AID”) 0 | 1 | 2 | 3 | 4 | 5
ActiveDry (see “OPTIONS AND FUNCTIONS”)
“1” = On, “0” = O 1 | 0
Light on the floor (see “OPTIONS AND FUNCTIONS”)
“1” = On, “0” = O 1 | 0
Sound
“1” = On, “0” = O 1 | 0
Factory Settings
Press START/Pause to restore to the factory
default all the values of the settings included
in the settings menu.
-
WATER SOFTENING SYSTEM
Water softener automatically reduces water hardness, consequently preventing
scale buildup on the heater, contributing also to better cleaning eciency.
This system regenerates itself with salt, therefore it is required to rell
the salt container when empty. The frequency of regeneration depends
on the water hardness level setting - regeneration takes place once per 4-6
Eco cycles with the water hardness level set to 3. The regeneration process
occurs at the beginning of the cycle with additional fresh water.
• Single regeneration consumes: ~3L of water;
• Takes up to 5 additional minutes for the cycle;
• Consumes below 0.005kWh of energy.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid dispenser should be A
lled when the RINSE AID REFILL indicator light in the control panel is lit.
1. Open the dispenser B by
pressing and pulling up the
tab on the lid.
2. Pour in the rinse aid (max.110
ml), making sure it does not
overow from the dispenser.
If this happens, clean the spill
immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can adjust
the quantity of rinse aid used.
To change, follow instructions in the section “SETTING MENU”.
If the rinse aid level is set to ZERO, no rinse aid will be supplied. The LOW
RINSE AID indicator light will not be lit if you run out of rinse aid.
A maximum of levels can be set according to the dishwasher model. 6
• If you see bluish streaks on the dishes, set a low number (0-3).
• If there are drops of water or limescale marks on the dishes, set
a mid-range number (4-5).
FILLING THE DETERGENT DISPENSER
To open the detergent dispenser use the opening device C. Introduce
the detergent into the dry dispenser D only. Place the amount of
detergent for pre-washing directly inside the tub.
1. When measuring out the detergent refer to the
mentioned earlier information to add the proper
quantity. Inside the dispenser , there are indicaD-
tions to help the detergent dosing.
2. Remove detergent residues from the edges of the
dispenser and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling
it up until the closing device is secured in place.
The detergent dispenser automatically opens up at
the right time according to the program.
Usage of detergent not designed for dishwashers may cause
malfunction or damage to the appliance.
A
B
D
C
Water Hardness Table
Level °dH
German degrees
°fH
French degrees
°Clark
English degrees
1 (Soft) 0 - 6 0 - 10 0 - 7
2 (Medium) 7 - 11 11 - 20 8 - 14
3 (Average) 12 - 16 21 - 29 15 - 20
4 (Hard) 17 - 34 30 - 60 21 - 42
5 (Very hard) 35 - 50 61 - 90 43 - 62
Specyfikacje produktu
| Marka: | Hotpoint |
| Kategoria: | Pomywaczka |
| Model: | H8I HT59 LS UK |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Hotpoint H8I HT59 LS UK, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Pomywaczka Hotpoint
20 Lutego 2025
6 Lutego 2025
8 Stycznia 2025
12 Grudnia 2024
12 Grudnia 2024
12 Grudnia 2024
12 Grudnia 2024
12 Grudnia 2024
12 Grudnia 2024
12 Grudnia 2024
Instrukcje Pomywaczka
- Kucht
- Rangemaster
- Godrej
- Cecotec
- Fulgor Milano
- Amica
- De Dietrich
- Bompani
- Kluge
- Altus
- Samsung
- Trieste
- Casselin
- Hestan
- Black & Decker
Najnowsze instrukcje dla Pomywaczka
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
8 Kwietnia 2025
8 Kwietnia 2025
8 Kwietnia 2025
8 Kwietnia 2025
8 Kwietnia 2025
7 Kwietnia 2025
7 Kwietnia 2025