Instrukcja obsługi Ikan RB-1F2H

Ikan światło RB-1F2H

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ikan RB-1F2H (4 stron) w kategorii światło. Ta instrukcja była pomocna dla 16 osób i została oceniona przez 8.5 użytkowników na średnio 4.1 gwiazdek

Pobierz PDF

Strona 1/4

QUIC TAR U EKS T G ID

RW5

Rayden Daylight Half x 1 LED Light

RB5

Rayden Bi-Color Half x 1 LED Light

RW10

Rayden Daylight 1 x 1 LED Light

RB10

Rayden Bi-Color 1 x 1 LED Light

CHECKED BY

What’s Included

1 x Light Fixture

1 x Yoke Mount

1 x Remote Control

1 x Power Supply w/ Cable

1 x AB Mount Battery Plate

1 x V-Mount Battery Plate

Getting to know your RAYDEN lights

PRECAUTIONS:

• Keep the ﬁxture away from water and all ﬂammable gases or liquids.

• Use only the recommended batteries.

• Handle the unit with care.

• DO NOT attempt to disassemble or repair the unit without ﬁrst contacting service department at

ikancorp.com.

• Keep the unit clean and free of dust. The unit can be cleaned with a soft dry cloth.

• Use only parts provided by the manufacture.

• Always use caution when plugging in the ﬁxture.

Mounting the Rayden to a Stand:

The Rayden LED Light comes with a pre-installed yoke and combo mount. This allows the ﬁxture to easily

sit and adjust on any stand. The 30° yoke gives the light free-range motion without obstructions. The Baby

" and Junior 1-

" Combo Pin allows the user a wide range of stands. The light can be mounted either

horizontally or vertically on a

" baby pin.

Power the LEDs:

The Rayden light comes with an included AC power supply and 6 foot cable. This allows the user to plug

into any standard 120-240v electrical outlet. The Rayden LED light can be powered from either an AB

Mount pro battery, or a V-Mount battery. The ﬁxture comes standard with either AB-Mount or V-Mount

plates. The plates can be easily removed and replaced for the type of batteries that are available.

Adjusting the Color & Brightness of the Light:

The Rayden LED light is controlled by the large yellow knob on the rear of the ﬁxture. The knob was

designed with the idea that it could be reached and adjusted when the

light is up on a stand. The knob

has three push settings.

1. The default setting is the brightness from 10%-100% brightness.

2. By pressing in on the knob the color temperature can be adjusted. (Bi-Color Lights)

Remote Control

The light can be adjusted also using the RF remote control. The use of the remote allows for multiple lights

to be connected as well as control of the brightness.

Optional Accessories

Some other products that work well with the RW10 available from Ikan include:

HD-STND

ROLLR-STND10

CP-STND-V3

SW-04

KCP-703

Heavy Duty Light Stand

2 Stage Roller Stand 10 ft 6 in

Compact Light Stand Version 3

Safety Wire

Stage Clamp w/ 16mm Stud

Remote Control Button Functions

• Press & Hold “A” for 5 seconds to sync remote control to light(s)

• Press “A” to power ON/OFF (for Daylight Light only)

• Press “A”& "B" to power ON/OFF (for Bi-Color Light only)

• Press “B” to adjust 4 levels of light intensity in increments of 25%

• Press and Hold “C” & “D” for 5 seconds to Enable/Disable sound

• Hold down “C” to increase light intensity 0%-100%

• Hold down “D” to decrease light intensity 100%-0%

Changing the Pro Battery Plate

Adding or removing the pro battery plate on the back of your ﬁxture can be easily achieved.

NOTE: The ﬁxture comes pre-installed with the Gold-Mount battery plate.

The process starts with the removal of the four screws on the four corners of the plate.

Once the screws are removed, separate the plate from the back of the ﬁxture.

Unplug the 2-pin connector from the ﬁxture.

Store the screws and the Gold-Mount in a safe place.

Reattaching the V-Mount plate is a simple process.

Plug the wired 2-pin connector into the ﬁxture where we just unplugged the Gold-Mount

plate at the back of the light. Orient the holes on the plate to match up with the screw holes

on the back of the ﬁxture. Using the screws supplied with the V-Mount plate, screw in the

plate until it is snug against the back of the ﬁxture. Do not over-tighten the screws.

You’re now ready to install your battery to the V-Mount plate.

Specyfikacje produktu

Marka:	Ikan
Kategoria:	światło
Model:	RB-1F2H
Kolor produktu:	Czarny
Temperatura barwowa (max):	5600 K
Kąt wiązki:	50 °
Rodzaj zasilania:	Prąd przemienny
Materiał obudowy:	Plastik
Ilość na paczkę:	3 szt.
Maksymalne zużycie mocy:	150 W
Kolor światła:	Biały
Kształt:	Kwadrat
Moc świetlna (max):	4559 lm
Współczynnik oddawania barw (CRI):	95
Liczba żarówek LED:	1184