Instrukcja obsługi Inverto Black Pro
Inverto
przełącznik
Black Pro
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Inverto Black Pro (4 stron) w kategorii przełącznik. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 5.5 użytkowników na średnio 4.4 gwiazdek
Strona 1/4
Technical parameters
Inputs 4 x IF inputs from Quattro LNB
1 x UHF/VHF input from Terrestrial antenna
Outputs 4 x loopthrough satellite IF outputs
1 x loopthrough terrestrial output
1 x Legacy output to connect to legacy receiver with combined
terrestrial signal
1 x Unicable output to connect up to 8 receiver tuners with com-
bined terrestrial signal
Frequency range Satellite: 950-2150MHz
Terrestrial: 47-862MHz
Loopthrough loss Satellite: max -3dB
Terrestrial: max -3dB
Gain Satellite: 10dB (min)
Terrestrial: no amplification
Isolation Satellite-Satellite outputs: min 30dB
Satellite-Terrestrial : min 35dB
Control protocol DiSEqC™ commands extension according to CENELEC
prEN50494
Power consumption 20VDC, 380mA
Dimensions (W x H x D mm) W=138.82 H=203.2 D=18.74 mm
Temperature range -20C - +60C
AC/DC adaptor Input voltage: 90-265VAC, 50/60Hz
Output voltage: 20VDC
Output current: 600mA
Short circuit protection: None
Troubleshooting
Make sure the satellite antenna and LNB are properly fixed, connected and adjusted and that the sat-
ellite receivers are installed, connected and switched on according to available instructions.
Ensure there is no short circuit on the product inputs. This will prevent power to the LNB. If this is the
case, disconnect the product from the main power, and then find and remove the short circuit on the
product inputs. Then re-connect the multiswitch to the main power.
Frequent defects are in connector joints i.e. if the central conductor is too short and fails to make
contact in the connector. Also the shielding braid should make proper contact with the connector coat.
Sometimes a reset to the multiswitch microprocessor is sufficient to remove a fault: simply disconnect
the multiswitch from main power for 30 seconds and then reconnect again.
If you are unable to remove the fault yourself, please contact your distributor.
Disposal
Following relevant EU directives, this device shall not be disposed of together with municipal waste.
Use local waste collection and recycling systems to dispose wore out products.
*
DiSEqC™ is a registered trademark of Eutelsat
*
For purpose of brevity, some product descriptions in this sheet remain at platform level and may not be
referred to as detailed datasheets of the products. Inverto Digital Labs reserves the right to amend, omit or
add products, product-lines, and/ or features without notice.
Installation manual
Unicable
™
Multiswitch
IDLP-UST111-CU010-8PP
4
V100214
Power In
20V DC, 380mA
V/H H/L H/H
Terrestrial
input
Satellite - Input
V/L
Terrestrial
input
Satellite - Input
V/H H/L H/HV/L
Terrestrial
output
Unicable Cascadable Switch
IDLP-UST111-CUO1O-8PP
Item: 3702
User Bands:
0 : 1076.06MHz 4 : 1484.30MHz
1 : 1178.12MHz 5 : 1586.36MHz
2 : 1280.18MHz 6 : 1688.42MHz
3 : 1382.24MHz 7 : 1790.48MHz
Satellite inputs: IF 950-2150MHz
Satellite Loop-Through loss: 3dB
Terrestrial Loop-Through loss: 3dB
Made in China
Designed in LU
Legacy Out
Unicable Out
TM
Satellite - loop-through output
+
V/H H/L H/HV/L
[+Terrestrial] [+Terrestrial]
Specyfikacje produktu
| Marka: | Inverto |
| Kategoria: | przełącznik |
| Model: | Black Pro |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Inverto Black Pro, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje przełącznik Inverto
30 Września 2024
Instrukcje przełącznik
- Powerfix
- Leviton
- TRENDnet
- Shimano
- Konig
- Atlona
- Cambium Networks
- IPGARD
- Phoenix Contact
- Vacmaster
- B-tech
- Matrox
- Tiptel
- Theben
- Yamaha
Najnowsze instrukcje dla przełącznik
9 Kwietnia 2025
9 Kwietnia 2025
7 Kwietnia 2025
5 Kwietnia 2025
4 Kwietnia 2025
4 Kwietnia 2025
4 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025
2 Kwietnia 2025