Instrukcja obsługi JL Audio Stealthbox SB-T-TACDC12/10TW3
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JL Audio Stealthbox SB-T-TACDC12/10TW3 (4 stron) w kategorii subwoofer. Ta instrukcja była pomocna dla 20 osób i została oceniona przez 10.5 użytkowników na średnio 4.8 gwiazdek
Strona 1/4
I N S T A L L A T I O N G U I D E
for the
SB-T-TACDC12/10TW3
SKU# 94557
2012 & Up Toyota Tacoma Double Cab
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system.
With proper installation, your new vehicle-specific enclosed subwoofer system
will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox® installed by your authorized
JL Audio dealer. The installation professionals employed by your dealer have the necessary tools
and experience to disassemble and reassemble your vehicle properly. If you prefer to perform your
own installation, please read this installation guide completely before beginning the process.
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox ® be properly mounted to the vehicle according to these
instructions. Failure to mount the enclosure properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
Continued on Next Page
SB-T-TACDC12/10TW3 INSTR_SKU# 011350
INSTALLATION
D I F F I C U LT Y :
25
OUT
OF
ESTIMATED TIME:
2 HOURS
S P E C I F I C A T I O N S
Enclosure Type: Sealed
Driver Type: 10TW3-D4
Nominal Impedance: 2 ohms
Continuous Power Handling: 400 watts (RMS method)
I N C L U D E D H A R D W A R E
(2) Brackets
(4) 1/4 - 20 x 1” Hex Bolt
(4) 1/4” Lock Washer
(4) 1/4” Flat Washer
(2) 1/4 - 20 U-Nut
SB-T-TACDC12/10TW3 INSTR_SKU# 011350
P O W E R R E C O M M E N D A T I O N
JL Audio recommends high quality ampliers such as the JL Audio XD300/1. The diagram below shows the recommended crossover settings for the XD300/1. For a detailed description of the amplier settings, consult the
owner’s manual for the amplier. If another amplier is being used, please reference this illustration and use similar settings on that amplier.
C O N N E C T I O N S
Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealthbox®. JL Audio recommends using a 4 AWG power kit such as the XD-PCS4-1B for your Stealthbox® amplier. Other kits
are available should you be using more than one amplier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used to provide signal for both channels of the amplier. JL Audio
reccomends using 12AWG speaker wire for subwoofers.
Continued on Next Page Page 2 • JL Audio, Inc., 2013
Continued on Next Page
SB-T-TACDC12/10TW3 INSTR_SKU# 011350
Page 3 • JL Audio, Inc., 2013
S T E P 4
On the backside of the rear panel, locate the two recessed
areas, then measure and mark 1” down the center from the
edge as shown. Drill a 1/8” pilot hole on the mark.
S T E P 8
Slide a 1/4 - 20 U-Nut through each of the 3/4” holes and
align them with the 7/16” holes as shown.
S T E P 3
Empty out the storage pocket. Remove the clips that hold in
the rear panel and remove the panel.
S T E P 7
Drill 3/4” holes on the marks made in the previous step. Use
caution so as not to drill through the back of the cab.
S T E P 2
Carefully unclip the seat bolt covers at the corners of the rear
seat backs. Unbolt and remove the seat backs.
S T E P 6
Measure and mark 1” to the right of each pilot hole. Enlarge
the 1/8” pilot holes in both the metal and the plastic to 7/16”.
Use caution so as not to drill through the back of the cab.
S T E P 1
Empty out the back seat of the vehicle and fold the seats
down.
S T E P 5
Reinstall the panel. Drill through the pilot holes made in the
previous step to create pilot holes in the metal. Use caution
so as not to drill through the back of the cab. Remove the
panel again.
Before drilling, always make sure that you are not
going to be drilling into any gas lines, brake lines,
tires, transmission lines, electrical wiring, exhaust
systems or anything else that might cause a reduction
in your weekly pay.
Always wear eye protection when drilling!
Specyfikacje produktu
| Marka: | JL Audio |
| Kategoria: | subwoofer |
| Model: | Stealthbox SB-T-TACDC12/10TW3 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z JL Audio Stealthbox SB-T-TACDC12/10TW3, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje subwoofer JL Audio
2 Kwietnia 2025
30 Grudnia 2025
30 Grudnia 2025
30 Grudnia 2025
30 Grudnia 2025
8 Grudnia 2024
8 Grudnia 2024
8 Grudnia 2024
13 Października 2024
6 Października 2024
Instrukcje subwoofer
- subwoofer Konig
- subwoofer Omnitronic
- subwoofer Extron
- subwoofer Tannoy
- subwoofer Argon
- subwoofer Teufel
- subwoofer Wharfedale
- subwoofer Skytec
- subwoofer Infinity
- subwoofer KRK
- subwoofer QTX
- subwoofer Martin Logan
- subwoofer OSD Audio
- subwoofer FBT
- subwoofer Ground Zero
Najnowsze instrukcje dla subwoofer
4 Kwietnia 2025
2 Kwietnia 2025
1 Kwietnia 2025
30 Marca 2025
19 Marca 2025
19 Marca 2025
19 Marca 2025
19 Marca 2025
19 Marca 2025
19 Marca 2025