Instrukcja obsługi JLab Crasher

JLab Kołyska/stacja dokująca Crasher

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JLab Crasher (6 stron) w kategorii Kołyska/stacja dokująca. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 6.5 użytkowników na średnio 4.8 gwiazdek

Pobierz PDF
Strona 1/6
CRASHER BLUETOOTH
WIRELESS STEREO SPEAKER
INSTRUCTION MANUAL
INTRODUCTION
Thank you for purchasing the Crasher. We are excited to welcome you to the JLab community. As an owner
of the Crasher portable Bluetooth speaker, we are here to help assist you with any product questions or issues
that come your way.
The Crasher ooth wireless speaker system applies the latest wireless technology that enables Bluet Bluetooth
you to enjoy , and hands free calls wherever wireless music, audio you want.
WHAT’S INCLUDED
1. The Crasher Bluet ooth stereo speaker
2. USB to Micro USB charging cable
3. 3.5mm to 3.5mm AUX audio cable
4. Power adapter with USB jack
5. Soft carrying pouch
FEATURES & BENEFITS
1. ooth tBlue Wireless Connectivity
2. Quality ound Hi-Fi stereo s
3. Hands free call control
4. attery devices Built In B Power Pack to charge your via full sized USB port
5. feet Use up to 33 away
6. Around 18 hours of operation time (median volume level)
GET TO KNOW THE CRASHER
1. Power On/Off Control
2. Battery Check / Bluetooth Pair Button
3. Pairing/Battery Check LED Indicators
4. Charging Red/Green LED Indicator
5. 3.5mm Audio In Jack to connect non BT devices
6. Micro USB Charge In Jack for charging the speaker
7. Telephone Call Button
8. Volume +
9. Volume –
10. USB Charging Out Jack (to external portable devices)
11. Microphone location
12. Speaker Drivers
13. Back Passive Woofer (located on back panel of unit)
1 - st Step CHARGING CRASHERTHE
1. Make sure the speaker is fully charged before initial use.
2. Connect the speaker via the Micro USB port (see item 6 above) to your PC or wall outlet using the Micro
USB cable and/or 5V Power Adapter.
3. The Battery LED (see item 4 above) will illuminate in red while charging and should become green once
fully charged. Another way to check if fully charged, ck the Battery Check button once (see item 2 . is to cli
above). If all 4 LED indicators light up, your Crasher is almost or fully charged. If only 1 3 of the LED –
lights light up, please continue charging your device.
4. JLab recommends charging the Crasher overnight with the Micro USB for optimum performance.
5. If you encounter any issues while using your Crasher, please first check to ensure device is fully charged
before troubleshooting the issue and contacting Support.
2nd Step - POWER UP
1. Once the Crasher is fully charged, l utton toggle switch ocate the Power B (see item 1 above).
2. Slide toggle to the right to power on. LED lights and sound should further indicate that the Crasher is on.
3. To power off, slide toggle to the left.
3rd Step - GET CONNECTED VIA BLUETOOTH
1. Crasher turned Make sure the is ON (See 1st and 2nd Step)
2. Press the Pair/Battery Check button and hold for about 5 seconds or until the 4 LEDs flash.
3. Bluetooth compatible device. Enable the searching mode on your (Most commonly found on your
smartphone under Settings, then Bluetooth, then by turning BT On / Searching for Devices.)
4. Select “ JLab Crasher” in the list shown on your Bluetooth device / smartphone.
5. a Enter “0000” if password is required.
6. When the Bluetooth connection is made, the first LED will flash slowly. – Please allow 10 20 seconds for
your device to connect.
7. Once connected, select your music, videos or calls and see your sound instantly amplified with the JLab
Crasher.
8. Please note, only one device may be connected at a time. To connect another Bluetooth device, you must
disconnect with the Crasher from your device / smartphone.
9. To reset the Crasher and void any existing connections, hold down the Pair/Battery Check button (see item

Specyfikacje produktu

Marka: JLab
Kategoria: Kołyska/stacja dokująca
Model: Crasher

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z JLab Crasher, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Kołyska/stacja dokująca JLab

JLab

JLab Crasher 2.0 Instrukcja

13 Sierpnia 2024
JLab

JLab Crasher Instrukcja

6 Sierpnia 2024

Instrukcje Kołyska/stacja dokująca

Najnowsze instrukcje dla Kołyska/stacja dokująca

Bigben

Bigben CBLNEONFLAMS Instrukcja

31 Marca 2025
Crestron

Crestron TSR-310-DS Instrukcja

26 Marca 2025
Alogic

Alogic DCAP-SPL Instrukcja

12 Marca 2025
Havit

Havit SK900BT Instrukcja

12 Marca 2025
LogiLink

LogiLink UA0410 Instrukcja

10 Marca 2025
Divacore

Divacore Blue Lagoon Instrukcja

27 Lutego 2025
Divacore

Divacore Mojito Instrukcja

27 Lutego 2025
Alogic

Alogic DX2 Instrukcja

11 Lutego 2025
Cyber Acoustics

Cyber Acoustics CA-920 Instrukcja

7 Lutego 2025
Cyber Acoustics

Cyber Acoustics PS-2370 Instrukcja

7 Lutego 2025