Instrukcja obsługi Juki CP-180
Juki
maszyna do szycia
CP-180
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Juki CP-180 (26 stron) w kategorii maszyna do szycia. Ta instrukcja była pomocna dla 184 osób i została oceniona przez 92.5 użytkowników na średnio 4.8 gwiazdek
Strona 1/26
ENGLISH
CP-180
INSTRUCTION MANUAL
No.02
40088353
i
CONTENTS
1. INSTALLING THE CONTROL PANEL ..........................................................................1
2. CONNECTING THE CORD ............................................................................................1
3. CONFIGURATION .........................................................................................................2
4. SETTING PROCEDURE OF THE MACHINE HEAD .....................................................2
5.
ADjUSTING THE MACHINE HEAD(direct-drive motor type sewing machine only)
...3
6. EXPLANATION OF THE CONTROL PANREL ..............................................................4
7.
HOW TO OPERATE THE CONTROL PANEL FOR SEWING STITCHING PATTERNS
...5
8. ONE-TOUCH SETTING .................................................................................................9
9. PRODUCTION SUPPORT FUNCTION .........................................................................9
10. HOW TO USE THE BOBBIN THREAD COUNTER ....................................................12
11. HOW TO USE THE THREAD TRIMMING COUNTER ................................................13
12. NEEDLE UP/DOWN COMPENSATION SWITCH .......................................................13
13. KEY LOCK FUNCTION ...............................................................................................14
14. ON/OFF SWITCH OF THE MATERIAL EDGE SENSOR ......................................14
15. AUTOMATIC THREAD TRIMMING SWITCH .........................................................14
16. ONE-SHOT AUTOMATIC STITCHING SWITCH ...................................................14
17. THREAD TRIMMING PROHIBITION SWITCH ......................................................15
18. FUNCTION SETTING SWITCH ...................................................................................15
19. OPTIONAL INPUT/OUTPUT SETTINGS ....................................................................16
20. AUTOMATIC COMPENSATION OF NEUTRAL POINT OF THE PEDAL SENSOR ...18
21. SETTING OF THE AUTO LIFTER FUNCTION ............................................................18
22. INITIALIzATION OF THE SETTING DATA ..................................................................19
23. CHECKING PROCEDURE OF THE ERROR CODE ...................................................19
- 1 -
1) Remove side plate setscrews 1 from the side plate.
2) Install control panel 2 on the machine head using screws 5, at washers 3 and rubber seat 4 sup-
plied with the control panel as the accessories.
1. INSTALLING THE CONTROL PANEL
< The relation between the respective machine heads and the positions of installing hole of the bracket are as described in the table. >
1 2 3 4 5 6
WARNING :
To prevent personal injury caused by abrupt start of the sewing machine, carry out the work after
turning OFF the power switch and ascertaining that the motor has completely stopped.
WARNING :
This Instruction Manual is for the control panel, CP-180.
Read "Safety Instructions" of the Instruction Manual for the control box carefully beforehand and
understand them before using CP-180.
In addition, be careful not to splash water or oil on it, or shock such as dropping and the like since
this product is a precision instrument.
1. DDL-9000B (Not provided with AK) is given as an example of installing procedure.
2. Screw to install the panel changes according to the machine head used. Refer to Table 1 and
conrm the kind of screw.
Table 1
Installing hole
Screw
DDL-9000A 1 - 5M5 X 12 Screw supplied with panel
as accessories
DDL-9000B 1 - 5
(Provided with AK)
M5 X 14 Side plate setscrew
(Not provided with AK)
M5 X 12
Screw supplied with panel
as accessories
LH-3500A 2 - 5M5 X 14 Side plate setscrew
1) Pass cord 1 of the control panel through hole A
in the machine table route it to the underside of
the table.
2) As for the connection of the connector, refer to
the Instruction Manual for the control box.
2. CONNECTING THE CORD
1
A
1
2
4
5
3
Specyfikacje produktu
| Marka: | Juki |
| Kategoria: | maszyna do szycia |
| Model: | CP-180 |
Pytania użytkowników
Jak regulować gęstość ściegu jest na max pokrętło nie działa
marian - 16 Grudnia 2024Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Juki CP-180, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje maszyna do szycia Juki
12 Stycznia 2025
30 Grudnia 2025
30 Grudnia 2025
30 Grudnia 2025
14 Października 2024
5 Października 2024
3 Października 2024
1 Października 2024
30 Września 2024
30 Września 2024
Instrukcje maszyna do szycia
- maszyna do szycia Mellerware
- maszyna do szycia Vendomatic
- maszyna do szycia Prince
- maszyna do szycia SteamMax
- maszyna do szycia Zippy
- maszyna do szycia Kohler
- maszyna do szycia Janome
- maszyna do szycia Mediashop
- maszyna do szycia Micromaxx
- maszyna do szycia Brother
- maszyna do szycia Lewenstein
- maszyna do szycia Empisal
- maszyna do szycia Solac
- maszyna do szycia Easy Home
- maszyna do szycia Bernina
Najnowsze instrukcje dla maszyna do szycia
8 Kwietnia 2025
5 Marca 2025
4 Marca 2025
1 Marca 2025
24 Lutego 2025
24 Lutego 2025
24 Lutego 2025
24 Lutego 2025
18 Lutego 2025
17 Lutego 2025