Instrukcja obsługi JVC VN-V225U

JVC Kamera monitorująca VN-V225U

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JVC VN-V225U (2 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 25 osób i została oceniona przez 13 użytkowników na średnio 4.4 gwiazdek

Pobierz PDF

Strona 1/2

VN-X235U is a high definition surveillance camera that uses CCD sensors with 4 times higher resolution

than VN-V225U.

Thank you for purchasing this JVC product.

Before operating this unit, please read the instructions carefully to ensure the best possible performance.

䡵The latest version

Please visit V.NETWORKS web site to check the latest firmware at

http://www.jvc-victor.co.jp/english/products-e.html

(The latest firmware can be found on V.NETWORKS B download page)

Installation

This manual describes procedures for “direct mounting to the ceiling or the wall”. For details on how to

“embed the camera into the ceiling”, “mount the camera with the cable pulled out from the side” and other

procedures, refer to [INSTRUCTIONS (Installation)] (pdf) in the supplied CD-ROM.

Note：

●Be sure to put on protective glasses to protect your eyes from falling objects when mounting the camera

to the ceiling.

●To mount the camera using an electrical box, please consult the dealer shop from which the camera is

purchased or any nearby JVC Service Centers.

Preparation

TTo mount the camera to a wall, perform the same procedures below but replace the word “ceiling” with

“wall”.

1Use the supplied template to open a hole in the ceiling (R35 mm), and pull out the

cables from the hole

Pull out the fall prevention wire, LAN cable, power cable, alarm cable, and audio cable that are attached to

the ceiling slab from the hole. (Fall prevention wire is not provided)

Note：

●Take note of the length, strength, pull and material (insulation) of the fall prevention wire.

●The inner diameter of the ring section of the fall prevention wire to be mounted to the camera should be

between R3.1 mm and R5.5 mm, and the outer diameter not larger than R9 mm.

2Turn the dome cover in the anti-clockwise direction to remove it

To prevent damage to the dome cover, a protection sheet is affixed.

3Grasp the inner dome and remove it from the catches (x2)

4Remove the outer casing

ALoosen and remove the fastening screw from the camera body using a screwdriver

BTurn the camera unit in the anti-clockwise direction to remove the outer casing

5Remove the attached fall prevention wire

Remove the fall prevention wire that is attached to the camera unit.

Cable Connection

For safety reasons, turn on the power only after all the connections are completed.

1Align the shooting direction with the shooting direction mark (j), followed by

mounting the outer casing to the ceiling

2Mount the supplied fall prevention wire on the camera unit to the fastening hook

3Mount the fall prevention wire that connects the camera and the ceiling to the camera

unit

4Connect the alarm cable

Connect the alarm cable to an external device, such as a sensor or buzzer.

5Connect the audio cable (shielded cable recommended)

6Connect the LAN cable

TTo use the PoE power supply, connect to a PoE-compatible device and supply the power from the LAN

cable.

●Connecting to HUB : Use a straight cable

●Connecting to a computer : Use a cross cable

7Connect the power cable

Power can be supplied to this unit either by connecting to an AC 24 V power supply or using PoE.

(For details on the use of PoE A [6 Connect the LAN cable])

Note：

●The power cable includes cable of the same color as the alarm cable. Check properly before connecting.

●Make sure that power is supplied using only one of the above methods at any one time. Connecting

simultaneously using the power cable and to PoE via a LAN cable may cause the camera to break down

or malfunction.

●By default the IP addresses of all the cameras are set to 192.168.0.2. If the power of multiple cameras

within the same LAN environment are turned on at the same time, the IP addresses of the cameras

overlap, thus preventing proper access. As such, make sure to turn on the power of the cameras one by

one and set the IP addresses such that there is no overlapping.

䡵Cable Types

䡵Power cable: Connection distance when using a 2-core VVF cable (reference values)

Note：

●For cables that are not used, be sure to wrap the ends individually with insulating tape.

●For safety reasons, turn on the power only after all the connections are completed.

Mounting the Camera Unit

1Insert the hooks (x2) of the outer casing into the holes (x2) of the camera unit

Note：

●Pay attention to prevent cables from being caught by the outer casing.

2Turn the camera unit in the clockwise direction

3Fasten the camera unit by tightening the fastening screw on it

Note：

●The camera will not be secured just by turning it in the clockwise direction. Be sure to fasten it with the

camera unit fastening screw.

This section describes procedures for adjusting the video image while checking the actual image on the

monitor.

Before touching the body of the camera, make sure that you touch the metal surface of the [MONITOR]

terminal to discharge any static electricity from your body. The static electricity may cause the camera to

malfunction.

1Connect the [MONITOR] terminal to the test monitor

2Set the [MONITOR OUT] selection switch to A BN or A BP , then turn on the power or

press the [RESET] button shortly (less than 2 seconds)

●The camera reboots. (approximately 1 minute)

●During rebooting, the [STATUS] indicator lights up in orange.

●Set to A BN when connecting to an NTSC monitor, and set to A BP when connecting to a PAL monitor.

3Adjust the shooting direction of the camera

Adjust the pan, tilt and rotation controls of the cameras to face the lens towards the subject.

Memo：

● ⬚ ⬚Rotate the lens in the pan and rotation directions ±175 and ±100 respectively from the positions

aligned with the camera’s shooting direction mark, pan center mark and rotation center mark. Be sure to

hold the rotation control and adjust the rotation without holding the lens section.

●After adjusting the field angle, tighten the tilt fastening screw to secure the camera so that its field angle

does not go out of alignment.

Note：

●Moving the camera when it has exceeded the adjustment range may cause its performance to

deteriorate.

●As the tilt and rotation range of this unit is wide, part of this unit may be reflected in the shooting screen

depending on the field angle and direction.

●Do not hold the lens section when adjusting the camera direction. The lens section may be damaged if

you apply force to it.

4Adjust the image size

Loosen the fastening screw of the zoom adjustment ring, move the ring to the left and right to adjust the

image size. After adjustment is complete, move the fastening screw toward the direction of the lens

(direction of the subject), and tighten accordingly.

5Roughly adjust the focus

ALift the focus adjust gear knob, and insert the catch into B in the diagram.

●The gear is disengaged.

Note：

●To prevent the gear shaft from breaking when the gear is opened too far out from B, remove the gear

shaft from the bearing (C in diagram). In this case, re-insert the shaft back into the bearing and return it

to the original position before using.

BLoosen the fastening screw of the zoom adjustment ring, move it to the left and right to adjust the focus.

6Fine adjust the focus

APress the [RESET] button for at least 2 seconds but less than 5 seconds.

●The camera enters the focus adjust mode and the [STATUS] indicator blinks in green and orange

alternately.

●The image is sharpened with the opening of the aperture.

●The center of the image is enlarged. (VN-X235U only)

●After adjusting the focus, press the [RESET] button for at least 2 seconds but less than 5 seconds to

cancel the focus adjust mode.

BShoot the subject.

CFine adjust the focus.

●Return the catch to A in the diagram, and then rotate the focus adjust gear knob to adjust the focus to

the optimum position.

DRotate the focus adjust gear knob about one base pitch in the direction of the arrow in the diagram.

●This is to correct the focus shift when mounting the dome cover.

ERemove the protective sheet, hold the dome cover over the lens and check the focus. After checking,

replace the protective sheet on the dome cover.

7Hold and press the focus adjust gear between your fingers in the direction of the

arrows in the diagram, and tighten the fastening screw of the focus adjustment ring

8After setting the [MONITOR OUT] selection switch to AOFFB, press the [RESET] button

shortly (less than 2 seconds)

●The camera restarts, and the focus assist mode is released. (approximately 1 minute)

Mounting the Dome Cover

After setting is complete, mount the dome cover.

1Mount the inner dome to the catches (x2)

2Mount the dome cover

ARemove and clean any dust or dirt on the dome cover.

BAlign the camera with the position alignment mark on the dome cover, and mount the dome cover.

3Remove the protective sheet

Note：

●When the cover is removed again after mounting the dome cover, check the field angle and re-adjust the

focus and field angle if necessary.

●Check to ensure that the dome cover is firmly mounted. The cover may fall off if it is not properly

mounted.

Continued on reverse side

䡵This manual contains the basic instructions for using this unit.

Please refer to [INSTRUCTIONS (Setting)] (pdf) and [INSTRUCTIONS (Installation)] (pdf) in the CD-ROM

supplied with this product for description on the detailed usage of this unit.

For the latest information, please refer to the A BREADME file in the CD-ROM supplied with this product.

●The supplied CD-ROM includes [INSTRUCTIONS (Setting)] (pdf), [INSTRUCTIONS (Installation)]

(pdf), [API Guide] (pdf), [VSIP Guide] (pdf), [Search tool], and [White Spot Correction Tool].

䡵How to read this READ ME FIRST

●JVC holds the copyright to this manual. Any part or all of this manual may not be reproduced without prior consent

from the company.

●Windows is a registered trademark of Microsoft Corporation in the U.S.

●Product names of other companies described in this manual are trademarks or registered trademarks of the

respective companies. Symbols such as 姠姞, and 姝 are omitted in this manual.

●Design, specifications and other contents described in this manual are subject to change for improvements without

prior notice.

Mounting the Camera

FIXD IP DOME CAMERA

VN-V225U

FIXD MEGAPIXEL IP DOME CAMERA

VN-X235U

READ ME FIRST

LST0930-001A

Camera unit

fastening screw

Inner dome

Dome cover

protective sheet

LAN cable

R35 mm

Fall prevention wire

(Not supplied)

Cables (power cable,

alarm cable, audio

cable, etc.)

Approx.

100 mm

outer casing

Alarm cable to be used (shielded cable recommended)

●Length of 50 m or shorter

●UL1007, UL1015 or equivalent products

●AWG#22 to AWG#18 or equivalent products

LAN cable to use

●STP (shielded cable recommended)

●Length of 100 m or shorter

●Category 5 and above

Type Color Signal name

Alarm cable Black

(Shielded cable)

Red Alarm input 1

Brown Alarm input 2

Orange Alarm output 1

Yellow Alarm output 2

Black GND

Audio cable Pink

(Shielded cable)

White Microphone input

Yellow GND

Black

(Shielded cable)

White Line output

Yellow GND

Power cable Red (Unshielded cable) AC 24 V Power Supply

Black (Unshielded cable)

Conductor diameter (mm) R1.0 and above 1.6 and above 2.0 and aboveR R

Maximum connection distance (m) 130 340 540

Caution

The rated power of this product is AC 24 V, 50 Hz/60 Hz. Make sure to use it with the correct voltage.

Be sure to use an AC 24 V supply that is insulated from the primary power source.

Supplying a power beyond the rated value may result in failures, smoke or fire. If the camera breaks down,

turn off the power and contact our service center immediately.

When a power beyond the rated value is supplied, the internal components may be damaged even if no

abnormality is found on the appearance and operation of the camera. Contact our Service Center

immediately to arrange for an inspection (charged separately).

FRONT

4, 5, 7

Solder welding or

crimping

Wind the insulation tape

Attach to fastening

hook

Align with shooting

direction

Fall prevention wire

(Not supplied)

Outer casing

mounting

screw

Below 2 mm

Adjusting Images

Hooks (x2)

Camera unit

fastening screw

Holes (x2)

2 , 6 3

[MONITOR] terminal

75 K terminated

Test monitor

Tilt : ±80 ⬚

Pan : ±175 ⬚

Rotation : ±100 ⬚

Shooting direction

mark

Pan center mark

Rotation center

mark

Rotation control

(x2)

[MONITOR OUT] selection switch

[RESET] button

Tilt fastening screw

[STATUS] indicator

6 7

Zoom adjustment ring

Focus adjustment ring

Focus adjust gear

One base pitch

Catch

Knob

Dome cover

Position alignment mark

Inner dome

Protective sheet

Specyfikacje produktu

Marka:	JVC
Kategoria:	Kamera monitorująca
Model:	VN-V225U
Kolor produktu:	Czarny
Wysokość produktu:	42.5 mm
Szerokość produktu:	202 mm
Głębokość produktu:	167 mm
Waga produktu:	780 g
Długość przekątnej ekranu:	7 "
Rozdzielczość:	480 x 234 px
Obsługiwane formaty audio:	MP3,WMA
Typ napędu:	Odtwarzacz DVD
Czas pracy na zasilaniu akumulatorowym:	3 h
Format kompresji zdjęć:	JPG