Instrukcja obsługi Kenwood NXR-710
Kenwood
Łączność radiowa
NXR-710
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Kenwood NXR-710 (16 stron) w kategorii Łączność radiowa. Ta instrukcja była pomocna dla 14 osób i została oceniona przez 7.5 użytkowników na średnio 4.5 gwiazdek
Strona 1/16
◆ Government law prohibits the operation of unlicensed radio
transmitters within the territories under government control.
◆ Illegaloperationispunishablebyneand/orimprisonment.
◆ Referservicetoqualiedtechniciansonly.
◆ Thisrepeaterisintendedforuseasaxedbasestationwith
the antenna located outdoors on the rooftop or on an antenna
tower.
◆ This repeater is designed for a 13.2 V DC power source!
Never use a 24 V DC or higher source to power the repeater.
◆ Use only the supplied DC cord.
◆ Do not remove the ferrite core attached to the DC cord. Doing
so may cause interference with radio communications.
THANK YOU!
We are grateful you purchased this Kenwood repeater. We
believe this easy-to-program repeater will be highly effective in
your communications system, and will keep personnel operating
atpeakefciency.
PRECAUTIONS
• Donotexposetheunittorainormoisture;topreventreor
electric shock.
• Donotopentheunitunderanycircumstances;toavoidrisk
of electric shock.
• Donotexposetheunittolongperiodsofdirectsunlight,nor
place it close to heating appliances.
• Donotplacetheunitinexcessivelydustyand/orhumid
areas, nor on unstable surfaces.
• If you detect an abnormal odor or smoke coming from the
unit, disconnect the power from the unit immediately. Contact
your Kenwood service center or dealer.
NOTICES TO THE USER
The AMBE+2TM voice coding Technology embodied in this product
is protected by intellectual property rights including patent rights,
copyrights and trade secrets of Digital Voice Systems, Inc. This voice
coding Technology is licensed solely for use within this Communications
Equipment.TheuserofthisTechnologyisexplicitlyprohibitedfrom
attemptingtoextract,remove,decompile,reverseengineer,or
disassemble the Object Code, or in any other way convert the Object
Code into a human-readable form. U.S. Patent Nos. #5,870,405,
#5,826,222, #5,754,974, #5,701,390, #5,715,365, #5,649,050,
#5,630,011, #5,581,656, #5,517,511, #5,491,772, #5,247,579, #5,226,084
and #5,195,166.
Firmware Copyrights
Thetitletoandownershipofcopyrightsforrmwareembeddedin
Kenwood product memories are reserved for Kenwood Corporation.
UNPACKING AND CHECKING EQUIPMENT
Note: The following unpacking information is for use by your Kenwood
dealer, an authorized Kenwood service center, or the factory.
Carefully unpack the repeater. We recommend that you identify
the items listed in the following table before discarding the
packing material. If any items are missing or have been damaged
duringshipment,leaclaimwiththecarrierimmediately.
Item Part Number Quantity
Hardwarexture J21-8559-XX 1
Front glass B10-2635-XX 1
Name plates B11-1259-XX 1
Cushion G13-1801-XX 4
Cushion G13-1802-XX 4
Foot J02-0475-XX 2
Foot J02-0492-XX 2
Grommet J59-0302-XX 2
Handle K01-0418-XX 1
Screws N30-4006-XX 2
Screws N35-3006-XX 5
DC cord E30-3427-XX 1
Lead wire with connector (15 pin) E31-3228-XX 1
Fuse F05-1537-XX 1
Instruction Manual B62-2200-XX 1
INSTALLATION
To install the handles onto the front panel of the repeater, align
the handles with the holes on the front panel, then secure the
handles using the supplied screws.
Please consult your dealer for installing the repeater and
antenna.
MICROPHONE
Connect an optional KMC-30, KMC-35, KMC-27A, KMC-27B,
or KMC-9C Kenwood microphone to the MIC jack on the front
panel.
NOTIFICATION
This equipment complies with the essential requirements of Directive
1999/5/EC.
The use of the warning symbol means the equipment is subject to
restrictions of use in certain countries.
This equipment requires a licence and is intended for use in the
countries as below.
AT BE DK FI FR DE GR IS
IE IT LI LU NL NO PT ES
SE CH GB CY CZ EE HU LV
LT MT PL SK SI BG RO
ISO3166
© B62-2200-00 (E)
09 08 07 06 05 04 03 02 01 00
VHFDIGITALBASE-REPEATER/UHFDIGITALBASE-REPEATER
INSTRUCTION MANUAL
NXR-710/NXR-810
Information on Disposal of Old Electrical and Electronic Equipment and
Batteries (applicable for EU countries that have adopted separate waste
collection systems)
Products and batteries with the symbol (crossed-out wheeled bin) cannot
be disposed as household waste.
Old electrical and electronic equipment and batteries should be recycled at
a facility capable of handling these items and their waste byproducts.
Contact your local authority for details in locating a recycle facility nearest
to you.
Proper recycling and waste disposal will help conserve resources whilst
preventing detrimental effects on our health and the environment.
Notice: The sign "Pb" below the symbol for batteries indicates that this
battery contains lead.
Specyfikacje produktu
| Marka: | Kenwood |
| Kategoria: | Łączność radiowa |
| Model: | NXR-710 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Kenwood NXR-710, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Łączność radiowa Kenwood
4 Lipca 2024
4 Lipca 2024
4 Lipca 2024
4 Lipca 2024
4 Lipca 2024
4 Lipca 2024
4 Lipca 2024
3 Lipca 2024
3 Lipca 2024
3 Lipca 2024
Instrukcje Łączność radiowa
- Multi Care Systems
- Wintec
- Spektrum
- Swissphone
- Albrecht
- President
- BaoFeng
- Wouxun
- Furuno
- Stabo
- Motorola
- Rexon
- ICOM
- Simrad
- Team
Najnowsze instrukcje dla Łączność radiowa
15 Stycznia 2025
15 Stycznia 2025
15 Stycznia 2025
14 Stycznia 2025
14 Stycznia 2025
14 Stycznia 2025
14 Stycznia 2025
27 Września 2024
27 Września 2024
27 Września 2024