Instrukcja obsługi Kenwood NXR-810
Kenwood
Łączność radiowa
NXR-810
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Kenwood NXR-810 (15 stron) w kategorii Łączność radiowa. Ta instrukcja była pomocna dla 19 osób i została oceniona przez 10 użytkowników na średnio 4.4 gwiazdek
Strona 1/15
1
◆ Government law prohibits the operation of unlicensed radio
transmitters within the territories under government control.
◆ Illegal operation is punishable by fine and/or imprisonment.
◆ Refer service to qualified technicians only.
◆ This repeater is intended for use as a fixed base station with
the antenna located outdoors on the rooftop or on an antenna
tower.
◆ This repeater is designed for a 13.2 V DC power source!
Never use a 24 V DC or higher source to power the repeater.
◆ Use only the supplied DC cord.
◆ Do not remove the ferrite core attached to the DC cord. Doing
so may cause interference with radio communications.
THANK YOU!
We are grateful you purchased this repeater. We KENWOOD
believe this easy-to-program repeater will be highly effective in
your communications system, and will keep personnel operating
at peak efficiency.
PRECAUTIONS
• Donotexposetheunittorainormoisture;topreventreor
electric shock.
• Donotopentheunitunderanycircumstances;toavoidrisk
of electric shock.
• Donotexposetheunittolongperiodsofdirectsunlight,nor
place it close to heating appliances.
• Donotplacetheunitinexcessivelydustyand/orhumid
areas, nor on unstable surfaces.
• Ifyoudetectanabnormalodororsmokecomingfromthe
unit, disconnect the power from the unit immediately. Contact
your KENWOOD service center or dealer.
NOTICES TO THE USER
UNPACKING AND CHECKING EQUIPMENT
Note: The following unpacking information is for use by your
KENWOOD dealer, an authorized service center, or the KENWOOD
factory.
Carefully unpack the repeater. We recommend that you identify
the items listed in the following table before discarding the
packing material. If any items are missing or have been damaged
during shipment, file a claim with the carrier immediately.
Item Part Number Quantity
Hardware fixture J21-8559-XX 1
Front glass B10-2635-XX 1
Name plates B11-1259-XX 1
Cushion G13-1801-XX 4
Cushion G13-1802-XX 4
Foot J02-0475-XX 2
Foot J02-0492-XX 2
Grommet J59-0302-XX 2
Handle K01-0418-XX 1
Screws N30-4006-XX 2
Screws N35-3006-XX 5
DC cord E30-3427-XX 1
Lead wire with connector (15 pin) E31-3228-XX 1
Fuse F05-1537-XX 1
Instruction Manual B62-2200-XX 1
INSTALLATION
To install the handles onto the front panel of the repeater, align
the handles with the holes on the front panel, then secure the
handles using the supplied screws.
Please consult your dealer for installing the repeater and
antenna.
MICROPHONE
Connect an optional KMC-30, KMC-35, KMC-27A, KMC-27B,
KMC-9C, or KMC-53 microphone to the jack on KENWOOD MIC
the front panel.
NOTIFICATION
This equipment complies with the essential requirements of Directive
2014/53/EU.
RESTRICTIONS
This equipment requires a licence and is intended for use in the
countries as below.
AT BE DK FI FR DE GR IS IE
IT LI LU NL NO PT ES SE CH
GB CY CZ EE HU MT PLLV LT
SK SI BG HR TRRO
ISO3166
B62-2200-60 (E)
VHF DIGITAL BASE-REPEATER/ UHF DIGITAL BASE-REPEATER
INSTRUCTION MANUAL
NXR-710/ NXR-810
Information on Disposal of Old Electrical and Electronic Equipment and Batteries
(applicable for countries that have adopted separate waste collection systems)
Products and batteries with the symbol (crossed-out wheeled bin)
cannot be disposed as household waste.
Old electrical and electronic equipment and batteries should be
recycled at a facility capable of handling these items and their waste
byproducts.
Contact your local authority for details in locating a recycle facility
nearest to you.
Proper recycling and waste disposal will help conserve resources
whilst preventing detrimental effects on our health and the environment.
© 2019
The AMBE+2TM voice coding Technology embodied in this product
is protected by intellectual property rights including patent rights,
copyrights and trade secrets of Digital Voice Systems, Inc. This
voice coding Technology is licensed solely for use within this
Communications Equipment. The user of this Technology is explicitly
prohibited from attempting to extract, remove, decompile, reverse
engineer, or disassemble the Object Code, or in any other way
convert the Object Code into a human-readable form. U.S. Patent
Nos. #8,315,860, #8,595,002, #6,912,495, #8,200,497, #7,970,606,
and #8,359,197.
Model Frequency range Max. output power
NXR-710-E TX/RX 136.000 - 174.000 MHz 50 W
NXR-810-E TX/RX 400.000 - 470.000 MHz 40 W
Firmware Copyrights
ThetitletoandownershipofcopyrightsforrmwareembeddedinKENWOOD
productmemoriesarereservedforJVCKENWOODCorporation.
Specyfikacje produktu
| Marka: | Kenwood |
| Kategoria: | Łączność radiowa |
| Model: | NXR-810 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Kenwood NXR-810, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Łączność radiowa Kenwood
4 Lipca 2024
4 Lipca 2024
4 Lipca 2024
4 Lipca 2024
4 Lipca 2024
4 Lipca 2024
4 Lipca 2024
3 Lipca 2024
3 Lipca 2024
3 Lipca 2024
Instrukcje Łączność radiowa
- BaoFeng
- Spektrum
- Rexon
- Stabo
- Albrecht
- Motorola
- GTV
- Wintec
- Multi Care Systems
- Simrad
- Vertex Standard
- Furuno
- ICOM
- Swissphone
- Team
Najnowsze instrukcje dla Łączność radiowa
15 Stycznia 2025
15 Stycznia 2025
15 Stycznia 2025
14 Stycznia 2025
14 Stycznia 2025
14 Stycznia 2025
14 Stycznia 2025
27 Września 2024
27 Września 2024
27 Września 2024