Instrukcja obsługi Leisure BSS1

Leisure zlewozmywak BSS1

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Leisure BSS1 (2 stron) w kategorii zlewozmywak. Ta instrukcja była pomocna dla 45 osób i została oceniona przez 23 użytkowników na średnio 4.6 gwiazdek

Pobierz PDF

Strona 1/2

05/04 1824

1. With soft sharp pencil, mark ﬁ nal position of sink top,

by measurement, on the work top allowing for clear-

ance of cabinet frame work.

2. Place sink-top in correct position on worktop then

reverse front to rear, not end for end.

With sharp soft pencil

draw round sink as

accurately as possible

making sure that this

outline coincides with

ﬁ nal position marked

previously.

3. Remove sink top and mark another line 20mm inside

the sink top outline, following the corner radii with

care.

This is the cutting line for the aperture.

4. Drill as large a hole as possible inside the cutting

line. Using a pad saw, jig saw or similar, cut out the

aperture to the cutting line.

5. The sink should then be placed in the aperture

where it will rest on the T-Nuts. The T-Nuts should

be marked round carefully with a pencil making sure

that the sink is parallel to the worktop edge.

6. The sink is then removed and a 8mm hole is drilled

on the centre of each T-Nut position, countersunk

on the underside of the worktop and counterbored

from the top with a 10mm diameter drill 13mm deep

to accept the T-Nut.

Stainless Steel Inset Sinks with T-nut Fixing

7. The sinktop should then be placed in position to check

for ﬁ nal ﬁ tting.

8. Turn the sink upside down and ﬁ ll the outer pe-

rimeter with a suitable sealing compound, (Bostik

Glazing Compound, Prestik Sealing Compound and

Arborseal have been found suitable). The sealing

compound should be sufﬁ cient to ﬁ ll the rim but any

excess should be pressed down with a warm knife so

that it is evenly spread around the sink perimeter.

9. Now ﬁ t the sink to the worktop, ﬁ rmly in position and

press down evenly if possible using heavyweights

around the perimeter. Enter the screws and screw

gently home. The weights will cause the sealing

compound to settle to the proﬁ le of the sink perim-

eter, and the screws will need to be tightened slowly

and gently or distortion of the sink perimeter will

result from too great a local pressure. After one hour

remove the weights and dress off any surplus com-

pound from around the sink ﬂ ange, with a wooden or

plastic spatula, taking care not to damage the plastic

laminate.

10. After twenty-four hours, check the tightness of the

T-Nuts but do not over-tighten. If the ﬁ xing screw bot-

toms because of over length, remove and hacksaw

12mm from end of thread, and reﬁ t.

Recommended tightening sequence for sink

ﬁ xing clips

Specyfikacje produktu

Marka:	Leisure
Kategoria:	zlewozmywak
Model:	BSS1
Kolor produktu:	Stal nierdzewna
Szerokość produktu:	508 mm
Głębokość produktu:	419 mm
Typ umywalka:	Zlew zamontowany na szczycie
Kształt zlewu:	Prostokątny
Wykonanie zlewu:	Stal nierdzewna
Liczba zlewów:	1 mis(y)
Kształt pierwszej komory:	Prostokątny
Wymiary pierwszej umywalki (SxD):	470 x 380 mm
Głębokość pierwszej umywalki:	195 mm
Otwór na baterię:	Tak
Bateria w zestawie:	Nie