Instrukcja obsługi Lenco CR-400 Wekkerradio
                    Lenco
                    
                    Radiobudzik
                    
                    CR-400 Wekkerradio
                
                                
    Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Lenco CR-400 Wekkerradio (2 stron) w kategorii Radiobudzik. Ta instrukcja była pomocna dla 18 osób i została oceniona przez 9.5 użytkowników na średnio 4.6 gwiazdek
                        Strona 1/2
                    
                    
                    
POWER
14
11
15
12
7
8
6
10
9
16
4
3
2
1
FRI SAT SUNTHUWEDTUEMON
AL
20
19
21 22
23
AC Connection
Press POWER till the POWER LED turns off. Insert the AC adaptor’s cable plug tip into the DC IN 
6V Jack at the back of the unit, then insert the moulded plug (with blades) into the wall outlet.
Note : Always Power off the unit before switching to AC adaptor supply.
In the event of AC power cut/off, user needs to readjust the Time and Alarm.
Install 4 pcs of `AA` size batteries (not included) into the battery compartment at the bottom of the 
unit (Alkaline is recommended for longer life). Be sure to observe the polarity markings which are 
engraved inside the battery compartment, then close the cover.
Note : Do not mix different type of battery or old batteries with new ones.
Install Battery
Display Backlight
Press   to turn on the LCD backlight for 7 seconds. Press other 
turn on the backlight plus activating their associated function.
SNOOZE/LIGHT buttons may also 
1. Press POWER till the Power LED turns off.
2. To activate the Alarm, press & hold UP for about 2 seconds till the `AL` icon turns on. The ` ` 
icon & Alarm Time appears for 2 seconds.
3. To deactivate the Alarm set, press & hold DOWN for about 2 seconds till the `AL` icon turns off.
Activate / Deactivate Alarm
Setting Clock Time
Setting Alarm Time
1. Press POWER till the POWER LED turns off.
2. Press & hold TIME SET for about 2 seconds. The `HOUR` digits will flash. Press UP / DOWN to 
set the hour. Press TIME SET to confirm the hour set.  After this, the `MINUTE` digits will flash. 
Press UP / DOWN to set the minute. Press TIME SET to confirm the minute set. Then  the 
`WEEKDAY`  Indicator  will  flash.  Press  UP  /  DOWN  to  select  the  desired  weekday  (MON  to 
SUN), press TIME SET to confirm the weekday set.
3. At any stage, if no key is pressed within the next 7 seconds (time out period), the last selected 
value is automatically saved.
1. Press POWER till the POWER LED turns off.
2. Press & hold AL SET for about 2 seconds till the Alarm On icon ` ` turns on. The `HOUR`digits 
will flash. Press UP / DOWN to set the hour. Press AL SET to confirm the hour set. After this, 
the `MINUTE` digits will flash.  Press  UP / DOWN  to  set the minute. Press AL SET to confirm 
the minute set. The ` ` icon disappears. The Clock Time is displayed.
3. At any stage, if no key is pressed within the next 7 seconds (time out period), the last selected 
value is automatically saved.
4. Short press UP or DOWN displays the ` ` icon & Alarm Time for 2 seconds.
Playback mp3 Music from your USB Drive / iPod shuffle
1. Make sure that your USB Drive/iPod shuffle contains music in mp3 format.
2. User MUST use the AC adaptor when playing iPod shuffle, otherwise the battery power will 
be drained away  by  the iPod. Always power off before inserting/removing the USB to/from the 
USB Port. 
3. Insert the USB Drive and press POWER till the POWER LED turns on.
4. The  LCD  displays  “rEAd”,  then  the  first  track  “0001”  is  played  automatically.  On  some  MP3 
Player you may need to press VII to start playing. 
5. Use  the  Buttons  on  this  unit  to  control  the  playback.  Short  press  Icc or  vvI  to  jump  to  the 
previous/next track. Long press Icc or vvI to fast scroll backward/forward to other tracks. Press 
VII to play/pause.
6. Press + / –  to turn the volume up/down, “L: 0 to L:15” is displayed.
Note : The Alarm Function will only work if the unit is in Power-Off (i.e. POWER LED turns 
off ; USB or AUX IN is not playing).
1. When the alarm time is reached, the ` ` icon flashes.
2. If USB Drive is docked, the first mp3 track “0001” is played automatically
  at factory-set volume level.
3. If USB Drive is not docked or battery power is too low to play the USB drive, then buzzer will 
sound instead.
1. Press SNOOZE/LIGHT to silent the USB/Buzzer temporarily for approx. 9 minutes. The Snooze 
function is repeatable in the next 120 minutes.
2. Press POWER or AL SET to cancel Snooze and reset the Alarm. The ` ` icon disappears. The 
alarm will sound again tomorrow at the same time.
3. The USB/Buzzer alarm will be reset automatically if no key is pressed in the next 120 minutes.
Snooze / Reset Alarm
Listening to AUX IN
1. Press POWER  till  the POWER  LED  turns on. Plug  one  end of  the  Line Cord into  the AUX IN 
Socket of this unit and the other into the Headphone Jack of the iPod, Mp3 Player, Discman or 
other music source.
2. Use the controls located on the external device to navigate, select, play the content and adjust 
the volume level.
Note :  When  the AUX IN  Jack  is  engaged,   the  output audio  signal  from the  USB  Drive  is 
muted.
Trouble Shooting
When powered  by Battery  alone and the  batteries are  running LOW, it may  not  be able  to 
read the USB Drive. Replace by new batteries.
If  this  device  hangs  and  is  not  responding  to  any  button  comand,  remove  all  batteries, 
unplug the  USB Drive, iPod, AUX  IN device, AC  Power Adaptor.  Wait for 1  minute  until all 
residual  power  is  drained.  Then  reinstall  new  batteries,  reconnect AC  Power Adaptor  and 
press POWER to power up again.
Alarm Sounded  - Wake by USB (mp3) / Buzzer
ENGLISH
POWER
Model : CR - 400
1
2SNOOZE / LIGHT Button
3BACKWARD Button
4POWER Button
5VOLUME - Button
6 Clock Display
7TIME SET Button
8DOWN Button
9UP Button
10 AL SET Button
11 Battery Compartment
12 Speaker
USB Port (Type A) 13
14 PLAY/PAUSE Button
15 FORWARD Button
16 POWER LED
17 DC IN 6V Jack
18 3.5mm AUX IN Jack
19 Alarm On Icon
20 Alarm Set Icon
21 HOUR Indicator
22 MINUTE Indicator
23 WEEKDAY Indicator
VOLUME + Button
13
5
17
18
Controls
AC Adaptor IN Jack & AUX IN Jack LCD Display
1
2SNOOZE / LIGHT-toets(DUTTEN / LICHT)
3ACHTERWAARTS-toets
4POWER-toets (Stroom)
5VOLUME - Toets
6 KLOK Uitleesvenster
7TIJDINSTELLING-toets
8OMLAAG-toets
9OMHOOG-toets
10 ALARMINSTELLING-toets
11 Batterijhouder
12 Luidspereeker
USB-Poort (Type A) 13
14 AFSPEEL / PAUZE-toets
15 VOORWAARTS-toets
16 POWER LED
17 DC IN 6V Ingang
18 3.5mm AUX IN Ingang
19 Alarm Instelling Icoon
20 Alarm Aan Icoon
21 UUR Indicator
22 MINUUT Indicator
23 WEEKDAG Indicator
VOLUME + Toets
Aansluiting van de AC
Plaats  4  stuks  AA  batterijen  (niet  bijgeleverd)  in  de  batterijhouder  aan  de  onderkant  van  het 
apparaat  (Alkalische  batterijen  zijn  aanbevolen  voor  een  langere  levensduur).  Zorg  ervoor  de 
polariteitsmarkeringen,  die  in  de  batterijhouder  zijn  gegraveerd,  te  controleren  en  sluit  dan  de 
afdekking.
Opmerking : Combineer geen verschillende type batterijen of oude met nieuwe batterijen.
Plaatsing van de Batterijen
Backlight (zwart licht) van het Uitleesvenster
Druk  op  SNOOZE/LIGHT om  het  backlight  van  het  LCD-scherm  7  seconden  lang  op  te  laten 
lichten. Het indrukken van andere toetsen kan tezamen met het activeren van hun geassocieerde 
functies het blacklight ook aanzetten.
Druk op POWER totdat de STROOM LED uitgaat. Steek de plug van het AC adaptersnoer in 
de DC IN 6V ingang aan de achterkant van het apparaat en steek vervolgens de stekker in 
het stopcontact.
Opmerking :  Schakel  het  apparaat altijd  uit  alvorens op  de  krachtbron  van de AC  adapter 
over te gaan. In het geval van een AC stroomuitvalling, zal de gebruiker de Tijd en het Alarm 
opnieuw moeten instellen.
Instelling van de Kloktijd
1. Druk op POWER totdat de STROOM LED uitgaat.
2. Druk en houd de TIJDINSTELLING-toets in voor ongeveer  2 seconden. De UUR-cijfers zullen 
oplichten. Gebruik  OMHOOG  / OMLAAG  om  het uur  in  te stellen. Druk  op  TIJDINSTELLING 
ter  bevestiging  van  het  ingestelde  uur.  Hierna  zullen  de  MINUUT-cijfers  oplichten.  Gebruik 
OMHOOG / OMLAAG  om de minuten in te stellen. Druk op  TIJDINSTELLING  ter bevestiging 
van  de  ingestelde  minuten,  vervolgens  zal  de  WEEKDAG-Indicator  oplichten.  Gebruik 
OMHOOG / OMLAAG om de gewenste weekdag (MON to SUN (MA tot VR)) te selecteren en 
druk op TIJDINSTELLING ter bevestiging van de ingestelde weekdag.
3. Als  tijdens  welke  fase  dan  ook  geen  toets  gedurende  7  seconden  (time-out  periode)  wordt 
ingedrukt, wordt de laatst geselecteerde waarde automatisch opgeslagen.
Instelling van de Alarmtijd
1. Druk op POWER totdat de STROOM LED uitgaat.
2. Druk  en  houd  de  ALARMINSTELLING-toets  in  voor  ongeveer  2  seconden  tot  het Alarm Aan 
` `- icoon aangaat. De UUR-cijfers zullen oplichten. Gebruik OMHOOG / OMLAAG om het uur 
in te stellen. Druk op ALARMINSTELLING ter bevestiging van het ingestelde uur. Hierna zullen 
de MINUUT-cijfers oplichten. Gebruik OMHOOG / OMLAAG om de minuten in te stellen. Druk 
op ALARMINSTELLING ter bevestiging van de ingestelde minuten. Het ` `-icoon verdwijnt. De 
Kloktijd wordt weergegeven.
3. Als  tijdens  welke  fase  dan  ook  geen  toets  gedurende  7  seconden  (time-out  periode)  wordt 
ingedrukt, wordt de laatst geselecteerde waarde automatisch opgeslagen.
4. Het kort indrukken van OMHOOG of OMLAAG zal het  ` `-icoon  & Alarmtijd voor 2 seconden 
weergeven.
1. Druk op POWER totdat de STROOM LED uitgaat.
2. Om het Alarm te activeren, druk en houd OMHOOG in voor ongeveer 2 seconden tot het  `AL`-
icoon aangaat. Het ` `-icoon & Alarmtijd worden voor 2 seconden weergegeven.
3. Om het ingestelde Alarm te annuleren, druk en houd OMLAAG in voor ongeveer 2 seconden tot 
het `AL`-icoon uitgaat.
Activeren / Annuleren van het Alarm
Alarm Gaat Af – Wordt wakker door USB (mp3) / Zoemer
Opmerking  :  De  Alarmfunctie  werkt  alleen  wanneer  het  Apparaat  uitstaat  (m.a.w.  de 
STROOM LED staat uit; USB of AUX IN worden niet afgespeeld).
1. Wanneer de alarmtijd is bereikt, licht het ` `-icoon op.
2. Als de USB-Drive is aangesloten, wordt het eerste mp3 nummer “0001” automatisch afgespeeld 
op het door de fabriek ingesteld volumeniveau.
3. Als  de  USB-Drive  niet  is  aangesloten  of  als  de  batterijen  te  zwak  zijn,  zal  als  alternatief  de 
zoemer klinken.
1. Druk op SNOOZE/LIGHT om de USB/Zoemer voor ongeveer 9 minuten tijdelijk uit te zetten. De 
SNOOZE-functie is herhaalbaar gedurende de volgende 120 minuten.
2. Druk op POWER of  ALARMINSTELLING om Snooze te annuleren en het Alarm opnieuw in te 
stellen. Het ` `-icoon verschijnt. Het alarm zal morgen op dezelfde tijd weer afgaan.
3. Als gedurende de volgende 120 minuten geen toets wordt ingedrukt, wordt het USB/ZOEMER-
alarm automatisch opnieuw ingesteld.
Snooze / Herinstelling van het Alarm
1. Zorg ervoor dat Uw USB-Drive/iPod wisselaar muziek bevat in mp3 formaat.
2. De gebruiker MOET de AC adapter gebruiken wanneer de iPod wisselaar wordt 
afgespeeld, anders worden de batterijen door de iPod volledig uitgeput. Zet het apparaat altijd 
uit alvorens het aansluiten/verwijderen van de USB op/van de USB-Poort. 
3. Plaats de USB-drive en druk op POWER tot de STROOM LED aangaat.
4. Het LCD-scherm vertoont "rEAd" en het eerste nummer “0001” wordt automatisch afgespeeld. 
Bij sommige MP3-spelers moet U misschien eerst op VII  drukken om het afspelen te starten.
5. Gebruik de Toetsen op dit apparaat om het afspelen te bedienen. Druk kort op Icc of vvI om 
naar het voorafgaande/volgende nummer te springen. Druk lang op Icc of vvI om versneld 
achterwaarts/voorwaarts te bladeren naar andere nummers. Druk op VII  om af te spelen of te 
pauzeren.
6. Druk op + / -  om het volume hoger/lager te zetten, "L: 0 tot L:15" wordt vertoond.
Afspelen van mp3 Muziek via Uw USB-Drive / iPod wisselaar
DUTCH
USB - DRIVE  LUIDSPREEKER
DIGITALE ALARMKLOK
Krachtbron: AC Adapter of Batterij
Opladen & Afspelen van mp3 op de iPod wisselaar
Speel mp3 af via USB-Drives
Afspelen van mp3 gebruikmakend van andere iPods (Window Format) De 
Dock Connector met USB 2.0 kabel In AC Krachtbronmode
Lokale Toetsen om de USB-Drive te
Bedienen Afzonderlijk Alarm met Snooze (Dutten)-
Vertoning van Tracknummer tot "999" functie
Vertoning van Volumeniveau "L 0 tot L15" Wordt Wakker door USB (mp3) / Zoemer
Aanzetten op het 1ste mp3 Nummer Klasse D Versterker
Aanzetten op de laatste Volume-Instelling Uistekende Stereo Geluid Weergave
iPod is een handelsmerk van Apple Computer, Inc., Geregistreerd in de V.S. en andere landen.
Simpele Instelling van Weekdag/ Uur/ Minuut
USB DRIVE SPEAKER
DIGITAL ALARM CLOCK
Power by AC Adaptor or Battery
Charge & Play mp3 on iPod shuffle
Play mp3 on USB Drives
Playback mp3 on other iPods (Window Format) using the Dock Connector 
to USB 2.0 cable in AC Power Supply mode
Local Buttons to Control USB Drive Easy Set Day of Week / Hour / Minute
Display Track Number upto “999” Single Alarm with Snooze Function
Display Volume Level “L 0 to L15” Wake by USB (mp3) / Buzzer
Power On to 1st mp3 Track Class D Amplifier
Power On to Last Volume Setting Excellent Stereo Sound Imaging
iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.
ENGLISH
If at any time in the future you should need to dispose of this product please note
that : Waste electrical products should not be disposed of with household waste.  
Please recycle where facilities exist.  Check with your Local Authority or retailer for 
recycling advice.
(Waste Electrical and Electronic Equipment Directive)
DUTCH
Indien u zich in de toekomst van dit toestel wenst te ontdoen, let er dan op dat 
elektrisch afvalmateriaal niet met het huishoudelijk afval mag worden verwijderd. 
Breng het toestel naar een kringloopwinkel of anderevoorziening voor recycling. Neem 
contact op met uw plaatselijke autoriteit of winkelier indien u meer informatie wenst 
over recycling.
(Richtlijn voor Afval van Elektrische en Elektronische Apparaten, AEEA)
ESPAÑOL
Si en el futuro necesita deshacerse de este producto, tenga en cuenta lo siguiente : 
no debe deshacerse de los residuos de productos eléctricos como si fueran residuos 
domésticos.  Por favor, recicle en los sitios en los que esto sea posible.  Acuda a las 
autoridades locales o al vendedor en busca de asesoramiento sobre reciclaje. 
(Directiva sobre residuos eléctricos y equipos electrónicos)
FRANÇAIS
Si vous souhaitez vous débarrasser ultérieurement du produit, veuillez noter que les 
déchets électriques ne doivent pas être jetés avec les déchets domestiques. Veuillez 
les faire déposer dans les centres de recyclage existants.  Contactez les autorités 
locales ou distributeurs pour obtenir de plus amples informations. 
(Directive de l' équipement électronique et des déchets électriques)
DEUTCH
Sollten Sie irgendwann zu späterer Zeit dieses Produkt entsorgen wollen, beachten 
Sie bitte Folgendes : Elektroschrott sollte nicht mit dem Haushaltsmüll entsorgt 
werden.  Bitte recyceln Sie ihn, sofern Ihnen entsprechende Möglichkeiten zur 
Verfügung stehen.  Setzen Sie sich mit Ihren kommunalen Behörden oder Ihrem 
Einzelhändler in Verbindung und fragen Sie diese um Rat bezüglich der 
Wiederverwertung.
(Elektro-und Elektronik-Altgeräte-Richtlinie (WEEE))
Beluisteren van AUX IN
1. Druk op POWER tot de STROOM LED aangaat. Steek het ene eind van het Verbindingssnoer 
in het AUX IN Contact van dit apparaat en het andere in de Hoofdtelefoon Ingang van de iPod, 
MP3-speler, Discman of andere muziekbron.
2. Gebruik de bedieningen van het externe apparaat om te navigeren, te selecteren, de inhoud af 
te spelen en het volumeniveau aan te passen.
Opmerking : Wanneer de AUX IN Ingang is verbonden, staat het uitgaande audiosignaal van 
de USB-Drive uit.
Wanneer het apparaat alleen op batterijen werkt en deze batterijen ZWAK zijn, zou het de 
USB-Drive niet kunnen inlezen. Vervang het met nieuwe batterijen.
Als dit apparaat hangt en niet reageert op enige toetsenbediening, verwijder dan alle 
batterijen, koppel de USB-Drive, iPod, AC Stroomadapter en het AUX IN apparaat af. Wacht 
voor 1 minuut lang totdat alle overige stroom is uitgeput. Herplaats dan nieuwe batterijen, 
sluit de AC Stroomadapter opnieuw aan en druk op POWER om het apparaat weer aan te 
zetten.
Probleemoplossing
Specyfikacje produktu
| Marka: | Lenco | 
| Kategoria: | Radiobudzik | 
| Model: | CR-400 Wekkerradio | 
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Lenco CR-400 Wekkerradio, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Radiobudzik Lenco
                        
                         2 Października 2024
                        
                    
                                                            
                        
                         12 Września 2024
                        
                    
                                                            
                        
                         12 Września 2024
                        
                    
                                                            
                        
                         11 Września 2024
                        
                    
                                                            
                        
                         7 Września 2024
                        
                    
                                                            
                        
                         2 Września 2024
                        
                    
                                                            
                        
                         31 Sierpnia 2024
                        
                    
                                                            
                        
                         30 Sierpnia 2024
                        
                    
                                                            
                        
                         29 Sierpnia 2024
                        
                    
                                                            
                        
                         27 Sierpnia 2024
                        
                    
                                                            Instrukcje Radiobudzik
- Kruger Matz
- Clarity
- Doro
- Conair
- Bresser
- Irox
- Geemarc
- Amazon
- Elro
- Muvid
- Lanaform
- OneConcept
- Braun
- Hyundai
- Yoko
Najnowsze instrukcje dla Radiobudzik
                        
                         15 Października 2024
                        
                    
                                                            
                        
                         9 Października 2024
                        
                    
                                                            
                        
                         9 Października 2024
                        
                    
                                                            
                        
                         9 Października 2024
                        
                    
                                                            
                        
                         9 Października 2024
                        
                    
                                                            
                        
                         9 Października 2024
                        
                    
                                                            
                        
                         9 Października 2024
                        
                    
                                                            
                        
                         9 Października 2024
                        
                    
                                                            
                        
                         9 Października 2024
                        
                    
                                                            
                        
                         8 Października 2024