Instrukcja obsługi LevelOne FNC-0104FX
LevelOne
Karta sieciowa/adapter
FNC-0104FX
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla LevelOne FNC-0104FX (2 stron) w kategorii Karta sieciowa/adapter. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 4 użytkowników na średnio 4.2 gwiazdek
Strona 1/2
FNC-0103/0104FX
Fast Ethernet 100Base-FX
User's Manual
(9802-Rev. D1)
1. Checklist
Before you start installing the FNC-0103/0104FX, verify that
the package contains the following items:
FNC-0103/0104FX Board
LAN Driver Diskette
This User's Manual
Please notify your sales representative immediately if any of
the aforementioned items is missing or damaged.
2. Overview
FNC-0103/0104FX is a PCI Fast Ethernet Board that fully
complies with all IEEE 802.3u, 100Base-FX standards. Four
LED indicators(LINK, ACT, COL and FDX) on the bracket
will help to oversee the network/board link, activities,
collision and full-duplex status.
3. FNC-0103/0104FX PCI Configuration
For motherboards with automatic PCI configuration:
No specific setup is needed
You can enter the system BIOS setup menu to view or
specify the interrupt line of the PCI slots
For motherboards with bus master & interrupt jumpers:
Enable bus master operation in a selected PCI slot and
select an interrupt (IRQ) level using the appropriate
motherboard jumper
Enable I/O on the FNC-0103/0104FX PCI slot
4. PCI Bus System & Configuration
• Ensure that the PCI machine does support master slots,
INT multiple sharing and timing compatibility. Do not
install FNC-0103/0104FX in PCI slave slots. Please refer
to your PCI system manual and select the appropriate
configuration settings.
1
• When installing multiple FNC-0103/0104FX boards at
the server station, you should correctly configure the
IRQ settings of the PCI slot. Up to four FNC-
0103/0104FX boards can be installed in a PCI file server
running NetWare system. The FNC-0103/0104FX server
boards share the same interrupt line with the driver
supporting multiple INT services at a time. Each FNC-
0103/0104FX's IRQ should not conflict with that of
other board.
• Operation in full or half-duplex(Default) mode is
configured by LAN driver options. The operating mode
should match the remote link device working status.
• You must use EMM386 version 4.49 or higher, and
install both DOS & EMM386 that came from the same
DOS package to avoid software problems.
5. Network Connection
100Base- -FX/TX network allows 512 bit time delay between
any two node stations in a collision domain. The Fiber/TP
cable with devices’ bit-time delay(round trip) are as below:
100Base 100Base-FX -TX
DTE↔DTE : 100 DTE↔DTE : 100
Class II Hub: 92 Class II Hub : 92
Fiber Cable : Cat. 5 TP Wire: 1.0 /m 1.112/m
DTE FX to DTE TX: 100
100Base-FX to 100Base-TX Converter: 56
The overall bit-time of Fiber/TP wires and devices must be
within 512 bit in a segment. You may use Switching Hub to
break up collision domain and extend the cabling distance.
Specyfikacje produktu
| Marka: | LevelOne |
| Kategoria: | Karta sieciowa/adapter |
| Model: | FNC-0104FX |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z LevelOne FNC-0104FX, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Karta sieciowa/adapter LevelOne
14 Października 2024
4 Października 2024
3 Października 2024
28 Września 2024
20 Września 2024
13 Września 2024
8 Września 2024
7 Września 2024
4 Września 2024
30 Sierpnia 2024
Instrukcje Karta sieciowa/adapter
- Micro Connect
- Alecto
- Riello
- Tycon Systems
- NUVO
- Grixx
- Akasa
- Code Corporation
- Barox
- Mikrotik
- Ewent
- ICIDU
- Lava
- Eaton
- Moxa
Najnowsze instrukcje dla Karta sieciowa/adapter
8 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
1 Kwietnia 2025
30 Marca 2025
29 Marca 2025
14 Marca 2025
14 Marca 2025