Instrukcja obsługi LogiLink AVM365
LogiLink
Kamera monitorująca
AVM365
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla LogiLink AVM365 (4 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 5 użytkowników na średnio 4.7 gwiazdek
Strona 1/4
1. Paste the installation sticker
supplied with this camera to
where to install the camera,
and position the four holes for
screws.
Drill the two screws at top to
the wall. ( and as shown
in the picture )
454Z
m565_365a_V1.0
2Prerequisite
Prerequisite (continued)
Before configuring network setup with iPhone / iPad, make
sure you have checked the followings:
(Recommended) Apply your own ADSL or cable
Internet service to simplify the network configurations.
Your camera is connected to your wireless router with
a RJ45 network cable, and it’s powered on.
You have installed our mobile program,
EagleEyes-Lite EagleEyes-Plus or , on your iPhone or
iPad.
iPhone / iPad
Network
Cable
(RJ45)
Wireless
Router
Modem
Camera
LAN Port WAN Port
Event Trigger
System Install the Camera
1
2. 161
Step4: Select “Apply” to confirm all your changes, and you see the message “Done” or “Fail” in “Status”.WAIT till
Done
Fail
Step6: Open your web browser on iPhone, and enter the IP address of your wireless router (“ ” in 192.168.2.161
our example) to access.
Step3: Select the IP address to enter the setting page, and switch the tab from “DHCP” to “Static”.
Then, note down the IP address and port number you see here. You’ll need them in Step 7.
Step5: In the new device page, give a meaningful name for this connection in “Title”, and select “Save”.
3Configure with iPhone / iPad
Step1: Connect your iPhone / iPad to the wireless router
which has the camera connected.
iPhone / iPad
Network
Cable
(RJ45)
Wireless
Router
Modem
Camera
LAN Port WAN Port
Step2: Open “EagleEyes-Lite” (or “EagleEyes-Plus”),
and click “+” to enter the new device page.
Then, select “Local Network Search” to search
your network camera.
The IP address shown is the address assigned to
your camera by your router.
1
B
A
A
B
You have checked the IP address used by your wireless
router as instructed below, and written them down.
You will need them later.
Connect your iPhone / iPad to the wireless router
with the camera connected, and go to “Settings”
“Wi-Fi”. Select “>” near the selected wireless network
to enter the details.
(Optional) Your wireless router supports UPnP, and
this function is enabled.
2
1
Note: Please leave some space between the
screws and wall. Do not get them to the end.
2. Hang the camera at the
screws you just fixed, and
make sure the camera
stays in place. Decide the
cable direction (up
/ down) before you fasten
the screws tight to the wall.
A
B
2
A
B
3. Drill the rest of screws ( and as shown in the
picture ) into the wall. After that, make sure all
screws are fastened.
3
C
D
C
D
3
4
4. Adjust the angle of the camera (up / down / left /
right) with the supplied wrenches for better viewing.
a.b.
Specyfikacje produktu
| Marka: | LogiLink |
| Kategoria: | Kamera monitorująca |
| Model: | AVM365 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z LogiLink AVM365, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Kamera monitorująca LogiLink
21 Września 2024
20 Września 2024
17 Września 2024
Instrukcje Kamera monitorująca
- Pioneer
- Topica
- Campark
- Acti
- Videcon
- Ernitec
- Lorex
- AirLive
- Logitech
- Burg Wächter
- Buffalo
- Exacq
- Petcube
- Brickcom
- Emos
Najnowsze instrukcje dla Kamera monitorująca
28 Stycznia 2025
25 Stycznia 2025
17 Stycznia 2025
17 Stycznia 2025
15 Stycznia 2025
13 Stycznia 2025
13 Stycznia 2025
13 Stycznia 2025
12 Stycznia 2025
12 Stycznia 2025